Инструкция по эксплуатации Vitek VT-1671 — страница 9

HOW TO USE OF YOUR MEAT MINCER

• This meat mincer is intended to mince boneless meat for household use only After assembling the appliance place it on a flat dry surface.

• Please ensure that the ventilation openings on the base unit are not blocked

• Make sure that local mains voltage corresponds to the operational voltage of the appliance.

• Connect the plug to the mains outlet.

• Place the food tray carefully Put a bowl or another container under the screen plate through which the mincemeat flows out.

• Before mincing make sure that the meat has thawed completely.

• Remove bones and excess far Rinse the meat and cut it into cubes or stripes to fit the food funnel

• Switch on the mincer by pressing the ON/OFF button (5)

• Slowly food the meat pieces into the food funnel using the pusher (1).

• Do not apply excess force to push the food through

you may damage the appliance Never use fingers or kitchen utensils to push the food through.

• There are chances that the meat will get stuck in the feeder screw during operation In such case use the reverse speed To do so switch off the appliance by pressing the ON/OFF button (5) let the motor stop completely and press the REV button (7) (Fig.

17) then resume operation after 6-10 seconds.

• Do not run the appliance for more than 15 minutes continuously After 15 minutes of continuous use let the appliance cool down to room temperature before further use.

• Once the task is over switch off the mincer and unplug before disassembling.

SCREEN PLATES (10 11,14)

The appliance is completed with three screen plates

for coarse medium and fine cutting.

Screen plates with big and medium openings are ideal for processing of raw meat vegetables nuts and dry fruit cheese fish etc.

Screen plates with small openings are ideal for processing of both raw and cooked meat fish etc.

VEGETABLE CUTTER (22 23 24)

The appliance is completed with three attachments:

two graters(23 24) and shredder (22).

HOW TO TAKE CARE OF YOUR MEAT MINCER

• Always switch off and unplug the appliance after use make sure that the motor has stopped completely before disassembling the appliance.

• Turn off the nut (15) use the key (9) if necessary and remove the screen plate and blade (13) from the feeder screw Remove the feeder screw (12)

from the mincer head (3)

Press the mincer button (4) turn the head anticlockwise and withdraw.

• Remove the food residues if any from the feeder screw.

• Wash all the parts in hot soapy water and allow to dry Never put the parts in the dishwasher

• Wipe the base unit (5) with a damp cloth

• Wipe the mincer screen plate and blade with salad oil before storing to prevent air corrosion.

• Kebbe attachments (18 19) and sausage attachments (16 17) shall be stores inside the pusher (1).

Fig 18.

• The power cord shall be stored in a special compartment at the bottom of the base unit Fig 16.

ATTENTION

• Always ensure that the bones and excess fat are removed from the meat before mincing.

• Always use only the pusher provided Never use

Your fingers or kitchen utensils

• Never immerse the base unit in water or other liquids.

• Never fix screen plates (10 11 14) and the blade (13) when using sausage or kebbe attachments.

• Do not try to mince food with hard fiber like ginger or horseradish.

• To avoid blocks and jams inside the feeder screw never apply excessive force.

• If the unit gets blocked due to hard foods lodged onto the feeder screw or cutting blade immediately switch off the appliance and remove the ingredient before starting again.

• When the circuit breaker activates do not switch on the appliance immediately Wait for about 60 seconds and start again using smaller force to push the food through

• When switching to the Reverse mode or vice versa wait for about 6 seconds to assure that the motor has stopped completely.

SPECIFICATIONS:

Power requirement: 220Â-230 V ~ 50-60 Hz

Maximum power: 1600 W.

Manufacturer has the right to modify the specifications without prior notice.

Service life of the appliance not less than 5 years

GUARANTEE

Details regarding guarantee conditions can be obtained from the dealer from whom the appliance was purchased The bill of sale or receipt must be produced when making any claim under the terms of this guarantee.

This product conforms to the EMC-

Requirements as laid down by the

Council Directive 89/336/EEC and to the Law Voltage Regulation (73/23 EEC)

ENGLISH

Vt-1671.qxd 10.01.05 11:28 Page 9