Добавить

Инструкция REMS 845004 — страница 9

Инструкция ФорматPDF Размер2,74 МБ Страниц104 КатегорияИнструменты / Контрольно-измерительные приборы ДобавилNikaДок779

Инструкция для REMS 845004 на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

← Назад
/ 104
Вперёд →
eng eng
2. Start-up
2.1. Electrical connection
WARNING
Caution: Mains voltage present!Beforeconnectingthepipecuttingmachine,
checkwhetherthevoltagegivenontheratingplatecorrespondstothemains
voltage.Onbuildingsites,inawetenvironmentorforsimilartypesofapplica-
tion,onlyoperatethepipecuttingmachineonthemainsviaa30mAfault
currentprotection(FIswitch).Observethecross-sectionnecessaryforthe
output of the pipe cutting machine when using an extension cable.
2.2. Installing the pipe cutting machine
REMS Cento
Fasten the pipe cutting machine e.g. to REMS Jumbo (Fig. 1) (Art. No. 120200)
or to the base frame (Fig. 2) (Art. No. 849315) with 4 or 2 M8 screws. Make
surethatthereisenoughroomforthepipecuttingmachine,REMSJumbo/
baseframeandthepipetobecut.LongerpipesmustbesupportedbyREMS
Herkules(Fig.2)(Art.No.120100)orREMSHerkulesY(Art.No.120130),on
bothsidesofthepipecuttingmachineifnecessary.Movethecuttingwheel
drive(1)forwardsbyturningthefeedlever(6)untilthepipetobecut(5)can
beplacedontherollers(3).TosettheheightofREMSHerkules,placethepipe
to be cut in the centre of the rollers (3) of the pipe cutting machine. Do not allow
thepipe(5)toknockagainstthecuttingwheel(2),thecuttingwheelcould
otherwisebedamaged.OpentheclampingleverofREMSHerkules,lowerthe
piperestofREMSHerkules,placeREMSHerkulesunderthepipenearthe
pipecuttingmachine,liftthepiperestagainstthepipeandtightentheclamping
lever.PlacethepresetREMSHerkulesundertheendofthepipe.Placeother
material rest(s) between the pipe cutting machine and the pipe end(s) if neces
-
sarytoreduceuntruerunningofthepipe.
1. Technical data
Use for the intended purpose
WARNING
REMS Cento and REMS DueCento are intended for the purpose of cutting and deburring the inside and outside of pipes.
All other uses are not for the intended purpose and are therefore prohibited.
1.1. Scope of Supply
REMSCentoBasic: Pipecuttingmachine,ringspannersize27/17,instructionmanual.
REMSDueCentoBasic: Pipecuttingmachine,ringspannersize27/17,2heightadjustablepiperests,feedlever,springplug,instructionmanual.
1.2. Article numbers REMS Cento REMS DueCento
Pipecuttingmachine 845000 845005
REMScuttingwheelCu-INOXforpipesofthepressttingsystemsof
stainlesssteel,copper,carbonsteel 845050 845050
REMScuttingwheelCuespeciallyforpipesofthepressttingsystemsofcopper 845053 845053
REMScuttingwheelStforsteelpipes,castpipes(SML) 845052 845052
REMScuttingwheelC-SFespeciallyforpipesofthepressttingsystems/pushtting
systemsofcarbonsteel,simultaneouslyproducesachamfer 845055 845055
REMScuttingwheelV,s10,forplasticandcompositetubes,wallthicknesss≤10mm 845051 845051
REMScuttingwheelP,s21,forplasticandcompositetubes,wallthicknesss≤21mm 845057
Base frame 849315
Rollers INOX (set) of tubular stainless steel 845110
Roller insert for cutting pipes Ø 40 – 100 mm 845060
Ring spanner size 27/17 849112 849112
REMSHerkules3B,materialrestwithtripod 120100
REMSHerkulesY,materialrestwithclampingdevice 120130
HeightadjustablepiperestØ100–225mm 845220
HeightadjustablepiperestØ40–100mm 845230
REMSJumbo,foldingworkbench 120200
REMSREG10–54E,outside/insidepipedeburrer 113835
REMSREG28–108,insidepipedeburrer 113840
REMSCleanM,machinecleaner 140119 140119
1.3. Area of application REMS Cento REMS DueCento
Stainlesssteelpipes,copperpipes,compositetubes,
Carbonsteelpipesofthepressttingsystems Ø(8)22–108mm Ø(54)108–225mm
SteelpipesDINEN10255(DIN2440) DN(10)20–100;(⅜”)¾–4” DN(50)100–150;(1½”)4–6”
Cast pipes (SML) DIN 19522 DN 40 – 100 mm DN (40) 100 – 200 mm
PlastictubesSDR11,compositetubes Ø(10)25–110mm Ø(50)–110mm
Wallthickness,copperpipes,castpipes(SML) ≤4.5mm ≤5.0mm
Wallthicknessplastic/compositetubes ≤10.0mm ≤21.0mm
1.4. Speed
Cutting wheel idle speed 115 rpm 115 rpm
1.5. Electrical data
230V~;50–60Hz;1,200W;5,7A.Fuse(mains)10A(B),intermittentmodeS320%(AB2/10min),protectiveinsulated,radiointerferencesuppressed,or
110V~;50–60Hz;1,200W;11,4A.Fuse(mains)20A,intermittentmodeS320%(AB2/10min),protectiveinsulated,radiointerferencesuppressed.
1.6. Dimensions REMS Cento REMS DueCento
L×W×H: 250×300×250mm(10”×12”×14”) 260×430×515mm(10.2”×16.9”×20.3”)
1.7. Weight
withoutsafetyfootswitch 17.8kg(39lb) 36.4kg(80.2lb)
1.8. Noise information
Acousticpressurelevel L
pA = 87 dB LpA = 87 dB
Acousticpowerlevel Lwa = 98 dB Lwa = 98 dB
Acousticpressurelevel L
pc peak = 100 dB Lpc peak = 100 dB
K = 3 dB K = 3 dB
1.9. Vibrations
Weightedrmsvalueofacceleration <2.5m/s² <2.5m/s²
K = 1.5 dB K = 1.5 dB
Thespeciedvibrationemissionvaluewasmeasuredaccordingtoastandardtestmethodandcanbeusedforcomparisonwithanotherdevice.Thespeciedvibra-
tionemissionvaluecanalsobeusedforaninitialestimationofthecut-out.
CAUTION
Thevibrationemissionvaluemaydifferfromthespeciedvalueduringactualuseofthepipecuttingmachinedependingonthemannerinwhichthepipecutting
machineisused.Dependingontheactualconditionsofuse(intermittentmode),itmaybenecessarytodenesafetymeasurestoprotecttheoperator.
Скачать «REMS 845004» — 2,74 МБ СкачатьСкачиваний: 0
Все руководства категории →
Нашли ошибку?