Инструкция REMS 845004 — страница 10

Инструкция

PDF

2,74 МБ

104

Инструменты / Контрольно-измерительные приборы

NikaДок779

Инструкция для REMS 845004 на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

REMS DueCento

 Placethepipecuttingmachineonarm,levelbase.Makesurethatthereis

enoughroomforthepipecuttingmachine,theheightadjustablepiperestsand

thepipetobecut.Pushthefeedlever(6)ontothespindle(8).Makesurethat

thereisapositivetbetweenthegrooveofthefeedleverandtheparallelpin

ofthespindleandpushthespringplug(9)intotheholesofthefeedleverand

thespindle(Fig.6).Longerpipesmustbesupportedwithheightadjustable

piperests(Fig.5)(10),onbothsidesofthemachineifnecessary.Movethe

cuttingwheeldrive(1)forwardsbyturningthefeedlever(6)untilthepipeto

becut(5)canbeplacedontherollers(3).Tosettheheightoftheheightadjust-

ablerests(10),placethepipetobecutinthecentreoftherollers(3)ofthe

pipe cutting machine. Do not allow the pipe (5) to knock against the cutting

wheel(2),thecuttingwheelcouldotherwisebedamaged.Opentheclamping

lever(11)oftheheightadjustablepiperests(10).Placetheheightadjustable

piperests(10)underthepipenearthepipecuttingmachine(Fig.7),liftagainst

thepipeandtightentheclampinglever(11).Placethepresetpiperestsunder

eachendofthepipe.Placeotherpiperest(s)betweenthepipecuttingmachine

andthepipeend(s)ifnecessarytoreduceuntruerunningofthepipe.

 DonotfastenREMSDueCentoandheightadjustablepiperests(10)tothe

base because otherwise a pipe running off centre could break the cutting wheel.

CAUTION

 REMSDueCentomayonlybemovedorcarriedbythefeedlever(6)whenthis

hasbeenlockedwiththespringplug(9)asdescribedabove.Otherwisethere

isadangerthatthefeedlever(6)willcomeawayfromthespindle(8).REMS

DueCentocanthenfalloverorfalloff.Danger of injury!

2.3. Fitting (changing) the cutting wheel (2)

 Pulloutthemainsplug!Choosesuitablecuttingwheel.Loosenthehexagonal

nut for fastening the cutting wheel (right-hand thread) with the size 27 ring

spannerprovided.Insert(change)cuttingwheel(2).Makesurethatthedriver

pinsofthedriveshaftengageintheholesofthecuttingwheel.Tightenthe

hexagonal nut.

NOTICE

An unsuitable cutting wheel will be damaged or the pipe will not be cut. Use

only original REMS cutting wheels!

2.4. Cutting pipes Ø 40 – 100 mm with REMS DueCento (Fig. 8)

 PlacerollerinsertforcuttingpipesØ40–100mm(14)(accessory)onthe

rollers(3).ForpipesØ40–70mmorforpipesØ70–100mm,placeroller

insertintherollers(3)asshowninFig.8.Longerpipesmustbesupportedby

heightadjustablepiperestsØ40–100mm(Art.No.845230,accessory),on

bothsidesofthepipecuttingmachineifnecessary.Cuttingpipes,see2.2.

REMS DueCento.

3. Operation

CAUTION

Danger of injury!

Wear suitable clothing. Do not wear loose clothing or jewellery. Keep hair,

clothing and gloves away from moving parts. Loose clothing, jewellery or

long hair can get caught in moving parts.

3.1. Work procedure

CAUTION

Support longer pipes (see 2.2)! The cut pipe sections can fall to the oor

immediately after being cut!

 Movethecuttingwheeldrive(1)forwardsbyturningthefeedlever(6)untilthe

pipe to be cut (5) can be placed on the rollers (3). Outside burr (sawing burr)

mustberemovedfromthepipeotherwisetherollerswillbedamaged.Make

sure that the REMS cutting wheel (2) suitable for the pipe to be cut is selected/

tted.Donotallowthepipe(5)toknockagainstthecuttingwheel(2)when

inserting,thecuttingwheelcouldbedamaged.Markthecuttingpointonthe

pipeandpositionittothecuttingwheel.Pressthesafetyfootswitch(7).Turn

thefeedlever(6)untilthecuttingwheelsetsthepipeinrotation.Thenturnthe

feedlever(6)approx.30°further(correspondstothehourdistanceonthedial

of a clock). Let the pipe turn about another 2 turns without further feeding before

re-engagingbya30°turnofthefeedlever.Repeattheprocess.

NOTICE

 Ifthecuttingwheelbreaksduringcutting,thesamegrooveinthepipetobe

cutmaynotbeusedafterchangingthecuttingwheel.Thechangedcutting

wheelwillbedamagedbyfragmentsleftinthegroove.

3.2. Supporting the material

 Longerpipesmustbesupported,onbothsidesofthepipecuttingmachineif

necessary(see2.2).

3.3. Deburring

Deburring of inside of pipe

 WiththeREMSREG28–108(12)pipesofØ28–108mm,Ø¾–4”canbe

deburredontheinside.TheREMSREG28–108isdrivenbyacuttingwheel

(Fig.3).ThecuttingwheelsREMScuttingwheelCu-INOX(Art.No.845050),

REMS cutting wheel Cu (Art. No. 845053) and REMS cutting wheel RF (Art.

No.845054)canbeusedfordriving.UseoneormoreREMSHerkules3B(Art.

No.120100),REMSHerkulesY(Art.No.120130)orheightadjustablepipe

rest(s) (10) for deburring longer pipes.

NOTICE

 Makesurethatthebladeofthecuttingwheel(2)protrudesintothegrooveof

the REMS REG 28 – 108 (12) (Fig. 3).

Deburring of outside/inside of pipes (Fig. 4)

 WiththeREMSREG10–54E(13)pipesofØ10–54mm,Ø½–2⅛”canbe

deburred on the outside and inside. There is a bit holder on the back of the

cuttingwheelshaftfordrivingtheREMSREG10–54E.Thepipestobe

deburredarepressedbyhandagainsttheREMSREG10–54Esetintorota

tionbythepipecuttingmachine.

NOTICE

 RemoveREMSREG10–54E(13)forcuttingpipes.Thebitholderisapproved

onlyforREMSREG10–54E.Othertoolswithbitholderarenotapproved.

4. Maintenance

4.1. Maintenance

WARNING

Pull out the mains plug before maintenance work!

Keep the rollers (3) of the pipe cutting machine and the roller insert (14) clean.

Cleanthespindle(8)andguidesofthecuttingwheeldrive(1)fromtimetotime

andgreaselightlywithmachineoil.Cleanheavilysoiledmetalpartswiththe

REMSCleanM(Art.No.140119)cleaner,forexample,andthenprotectagainst

rust.

 Cleanplasticparts(e.g.housing)onlywiththeREMSCleanMmachinecleaner

(Art. No. 140119) or a mild soap and a damp cloth. Do not use household

cleaners. These often contain chemicals which can damage the plastic parts.

Neverusepetrol,turpentine,thinnerorsimilarproductstocleanplasticparts.

 Makesurethatliquidsnevergetinsidethepipecuttingmachine.

4.2. Inspection / maintenance

WARNING

Pull out the mains plug before carrying out maintenance or repair work!

Thisworkmayonlybeperformedbyqualiedpersonnel.

The gear of REMS Cento and REMS DueCento is maintenance-free. It runs

inalife-longgreasellingandthereforeneedsnolubrication.Themotorhas

carbonbrushes.Thesearesubjecttowearandmustthereforebycheckedand

changedbyqualiedspecialistsoranauthorisedcustomerserviceworkshop

fromtimetotime.OnlyuseoriginalREMScarbonbrushes.Seealsopage5.

Behaviourintheeventoffaults.

eng eng

Скачать «REMS 845004» — 2,74 МБ СкачатьСкачиваний: 0

Инструкция REMS 845004 — страница 10

Другие руководства из этой категории