Инструкция по эксплуатации WORX Tools WU601.1 — страница 11

Router ENG

• When vacuuming dry dust that is especially detrimental to health or carcinogenic use a special vacuum cleaner.

3 ON AND OFF SWITCH

For starting the machine actuate the lock-off button (16) first and then press and hold the

On/Off switch (18) afterwards.

Speed Pre-selection

The required speed can be pre-selected with the thumb-wheel (17) (also whilst running).

1 – 2 = low speed

3 – 4 = medium speed

5 – 6 = high speed

The required speed is dependent on the material and can be determined by practical testing.

After longer periods of working at low speed allow the machine to cool down by running it for approx 3 minutes at maximum speed with no load.

Speed Table

Material

Router bit-Ø Speed stages

Hardwood (Beech)

4 – 10mm

12 – 20mm

22 – 40mm

Softwood (Pine)

4 – 10mm

12 – 20mm

22 – 40mm

Particle board

4 – 10mm

12 – 20mm

22 – 40mm

Plastic

4 – 15mm

16 – 40mm

Aluminum

4 – 15mm

16 – 40mm

The values shown in the chart are standard values The necessary speed depends on the material and the operating conditions and can be determined by practical testing.

Constant Electronic Control and Soft Start (Only for WU601&WU601.1)

Constant electronic control maintains the speed constant at no-load and under most working conditions Soft start delays the increase in motor speed to reduce the motor “kick” or torque effect to improve operator comfort and safety.

4 SETTING THE DEPTH-OF-CUT

Depending on the cutting operation the depth of cut can be preset in several steps.

The adjustment of the depth-of-cut may only be carried out when the router is switched off.

Coarse Adjustment of the Depth-of-cut

Place the router on the work-piece to be machined.

Set the fine adjustment for depth-of-cut in the center position with fine-adjustment knob (1); to do this turn the fine-adjustment knob until the markings (23) on the backside of the router are in alignment as shown Afterwards turn scale (2) to “0” (See C) Set step buffer (9) to the lowest position; the buffer snaps-in noticeably.

Loosen locking screw (7) so that depth stop (6) can be moved freely.

Release the clamping lever (3) by turning in clockwise direction and slowly lower the router until the router bit touches the surface of the workpiece Lock the router in position by turning the clamping lever in anti-clockwise direction.

Press depth stop downwards until it touches the stop buffer (9) Adjust the depth stop (6) to the required routing depth and tighten the wing screw (7) Release the clamping lever and guide the router back up again.

The coarse adjustment of the depth-of-cut should be checked by a trial cut and corrected if necessary.

Fine Adjustment of the Depth-of-cut

After a trial cut fine adjustment can be carried out by turning the fine adjustment knob (1 scale mark = 0.1 mm/1 rotation = 2.0 mm) The maximum adjustment is approx

+/– 8 mm.

Example: Slide router upwards again and measure the depth-of-cut (set value = 10.0 mm; actual value = 9.8 mm).

Lift up router and underlay guide plate (11) in such a manner that the router can plunge freely without the router bit touching the work-piece

Lower the router again until the depth stop touches the step buffer (9).

Afterwards set scale (2) to “0”.

Loosen wing screw.

With the fine adjustment (1) advance the depthof-cut in clockwise direction by 0.2 mm/

2 scale marks (= difference between required 11

UKR-WU600 WU600.1 WU601 WU601.1-M-060726.indd 11

2006-7-26 14:08:54