Добавить

Инструкция SKIL 8003 CC — страница 8

Инструкция ФорматPDF Размер5,85 МБ Страниц196 КатегорияИнструменты / Контрольно-измерительные приборы ДобавилОлегMaster

Инструкция для SKIL 8003 CC на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

← Назад
/ 196
Вперёд →
8
upright position; when doing so, make
sure no combustible materials or
inammable gases are in the proximity
• Do not store/leave the tool outdoors
• Store the tool in a dry and locked-up
place, out of reach of children
USE
• On/o switch with 3 temperature
settings 4
!  check if switch A 2 is in 
position “0” before plugging in
- switch on the tool by pushing
switch A in desired position:
1 = 50°C, air ow 250 litres/minute
2 = 400°C, air ow 250 litres/
minute
3 = 570°C, air ow 500 litres/
minute
- when using it for the rst time,
some smoke may emit from the
tool; this is normal and will soon
cease
- switch o the tool by pushing
switch A in position “0”
• General use
- determine the right temperature by
testing out on an inconspicuous
part of the workpiece; start with a
low temperature setting
- the temperature falls as the
distance between the air outlet/
nozzle and the workpiece
increases
- the temperature required depends
on the material to be worked on
• Stationary use 5
- set the tool down on its rear in an
upright position
- make sure the surface is clean and
dustfree; polluted air damages the
motor
- make sure the air ow is directed
away from you
- secure the cord to prevent pulling
down the tool
- do not touch the air outlet/nozzle
- make sure nothing drops into the
air outlet/nozzle
- carefully hold the tool with one
hand while switching it o with the
other hand, and then allow it to
cool down
• Use at hard-to-reach places
- remove ring B 2, thus releasing
the metal air outlet over a greater
distance
!  pay attention to increased risk 
of fire and burns
• Holding and guiding the tool 6
- hold the tool with one hand
- keep ventilation slots E 2
uncovered
• SKIL accessories (not standard 
included) 7
- glass protection nozzle F (for
deecting air ow)
- at nozzle G (for broadening air
ow)
- reector nozzle H (for reecting air
ow)
- reduction nozzle J (for
concentrating air ow)
All application examples (except 
removing paint next to glass) can
be performed without accessories;
however, using the appropriate
accessory simplies the work and
signicantly improves the quality of the
results
• Mounting/removing accessories
(not standard included)
- simply t the accessory onto air
outlet C 2
- remove an accessory by pulling it
o to the front after it has cooled
down
!  mount an accessory only when 
the air outlet is cold, when the 
switch is in position “0” and 
when the plug is disconnected
• Constant heat control (overload
protection)
Protects heating element from
damage when tool is overloaded
without having to stop it and/or let it
cool down for a period of time
- when the temperature gets too
high, the heating element switches
itself o, while the motor continues
to run and produces cold air
- when the temperature has fallen
down suciently (taking only a few
seconds), the heating element will
be switched on automatically
Скачать «SKIL 8003 CC» — 5,85 МБ СкачатьСкачиваний: 0
Все руководства категории →
Нашли ошибку?