Инструкция SKIL 8003 CC — страница 7

Инструкция

PDF

5,85 МБ

196

Инструменты / Контрольно-измерительные приборы

ОлегMaster

Инструкция для SKIL 8003 CC на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

capabilities, or lack of experience and

knowledge, unless they have been

given supervision or instruction

concerning use of the tool by a person

responsible for their safety

• Always check that the supply voltage

is the same as the voltage indicated

on the nameplate of the tool

• Be sure tool is switched o when

plugging in

DURING USE:

• Handle the tool with care; prevent

fire and burns

- do not touch the air outlet/nozzle

and the heated object; they

become extremely hot

- do not hold the air outlet/nozzle too

close to the object to be worked on

- do not direct the hot air ow

towards the same surface for too

long

- never look down the air outlet/

nozzle

- wear protective gloves and use

safety glasses

- never direct the hot air ow towards

persons or animals

- never use the tool for drying hair

- do not leave the tool unattended

- never use the tool in the proximity

of inammable gases or

combustible materials (risk of

explosion)

- when working with plastic, paint,

varnish and similar materials,

inammable and poisonous gases

may be produced; inform yourself

beforehand about the materials to

be worked on

- take into account, that heat may be

transferred to combustible

materials out of eyesight

- to be on the safe side, have a

bucket of water or a re

extinguisher handy, in case any

material catches re

• Prevent electrical shock

- never poke anything down the air

outlet/nozzle

- avoid body contact with earthed

surfaces (e.g. pipes, radiators,

ranges, refrigerators)

- ensure the tool does not get wet

- do not use the tool in damp

locations

- when used outdoors, connect the

tool via a fault current (FI) circuit

breaker with a triggering current of

30 mA maximum, and only use an

extension cord which is intended

for outdoor use and equipped with

a splashproof coupling-socket

• Handle the cord with care

- always keep away the cord from

the hot air ow and the air outlet/

nozzle

- keep the cord away from heat, oil

and sharp edges

- do not carry the tool by the cord,

and do not yank the cord to

disconnect it from the socket

- do not suspend the tool by the cord

• Never use the tool in conjunction with

chemical solvents

• Make sure work area is adequately

ventilated

• Keep work area clean and well lit

• Keep children away from work area

• Ensure that children do not play with

the tool

• Inrush currents cause short-time

voltage drops; under unfavourable

power supply conditions, other

equipment may be aected (if the

system impedance of the power

supply is lower than 0,127 +

j0,079 Ohm, disturbances are unlikely

to occur); if you need further

clarication, you may contact your

local power supply authority

• Stay alert; watch what you are doing,

use common sense and do not

operate the tool when you are tired

• Take a secure stance; do not

overreach, especially on ladders and

stages

• Ensure that the tool is switched o,

before putting it aside

• In case of electrical or mechanical

malfunction, immediately switch o

the tool and disconnect the plug

AFTER USE:

• Switch o the tool and disconnect the

plug

• Allow the tool to cool down for at

least 30 minutes before storage

• Suspend the tool on hanging ring

D 2 or set it down on its rear in an

Скачать «SKIL 8003 CC» — 5,85 МБ СкачатьСкачиваний: 0

Инструкция SKIL 8003 CC — страница 7

Другие руководства из этой категории