Инструкция SKIL 0750 RA — страница 9

Инструкция

PDF

8,93 МБ

152

Садовая техника

OlegTech20

Инструкция для SKIL 0750 RA на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

CHArGING/BATTerIes

• Charge battery only with the charger that is supplied with

the tool

• Do not touch the contacts in the charger

• Do not charge battery in damp or wet environments

• When charging the battery, place the charger on a at

non-ammable surface and away from combustible

materials

• Do not expose tool/charger/battery to rain

• Store tool/charger/battery in locations where temperature

will not exceed 40°C or drop below 0°C

• Do not use charger when damaged; take it to one of the

ocially registered SKIL Service Stations for a safety

check

• Do not use charger when cord or plug is damaged; cord

or plug should be replaced immediately at one of the

ocially registered SKIL Service Stations

• Do not use battery when damaged; it should be replaced

immediately

• Do not disassemble charger or battery

• Do not attempt to recharge non-rechargeable batteries

with the charger

EXPLANATIONOFSYMBOLSONTOOL/CHARGER/

BATTerY

3Readtheinstructionmanualbeforeuse

4Donotexposetool/charger/batterytorain

5Warning! After switching o the tool the blade continues

to move for a few seconds

6 Payattentiontotheriskofinjurycausedbyflying

debris (keep bystanders a safe distance away from work

area)

7 Only use the charger indoors

8 Double insulation (no earth wire required)

9 Fail-safe isolating transformer (the power source is

electrically separated from the transformer output)

0 Automatic shut-o when charger gets too hot (thermic

fuse blows and charger becomes useless)

! Incorrect polarity of the charger connection could cause

a hazard (only charge the battery with the charger

supplied)

@ Do not dispose of the charger together with household

waste material

# Do not dispose of the battery together with household

waste material

$ NiMH technology provides more energy in a less

environment-polluting way

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• If for any reason the old plug is cut o the cord of the

charger, it must be disposed of safely and not left

unattended

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of the charger to the earth terminal of the plug

Use

• Charging battery %

- battery of new tools is not fully charged

! removebatteryAfromchargerBaftercharging

periodhasendedtherebylengtheningtheservice

lifeofthebattery

IMPORTANT:

- after 3 hours the charging operation will be completed,

and the battery may be used, eventhoughthered

lightmaystillbeon (the red light may require more

than 3 hours to turn o)

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- ensure that the outside surface of the battery is clean

and dry before inserting into charger

- do not charge at temperatures below 0°C and over

40°C; this will seriously damage the battery as well as

the charger

- do not remove battery from tool while it is running

! abatterythatisneworhasnotbeenusedfora

longerperioddoesnotdevelopitsfullcapacityuntil

afterapproximately5charging/dischargingcycles

- do not repeatedly recharge the battery after only a few

minutes of operation; this may result in a reduction of

operating time and battery eciency

- if you anticipate long periods of non-use for the tool, it

is best to unplug the charger from its power source

• On/o safety switch ^

Prevents the tool from being switched on accidentally

- switch on tool by rst pressing safety switch C 2 and

then pulling trigger switch D 2

- switch o tool by releasing trigger switch D

- move tool away from cutting area before switching o

! afterswitchingoffthetoolthebladecontinuesto

rotateforafewseconds

• Changing blades &

! removebatteryfromtool

! wearprotectivegloves

- turn tool upside down

- push release button E

- slide protective cover F in same direction as arrow

printed on cover and lift it from the housing

! becarefulwhenliftingtheprotectivecover;the

shrubshearbladeinparticularmayfalldown

unexpectedly

- lift blade G or H out and mount required blade as

illustrated

- position protective cover F back and slide it towards

the blade until it snaplocks

• Holding and guiding the tool

! whileworking,alwaysholdthetoolatthe

grey-colouredgriparea(s)*

- maintain a stable working position

- keep your other hand away from the cutting blades

• Trimming hedges (

- trim the sides of the hedge rst (from the bottom

upwards), then cut the top

- trim the side of a hedge in such a way that it will be

slightly narrower at the top

- use a hand saw or pruning shears to cut thicker branches

- shrub shear blade H as well as grass shear blade G

can be used for trimming hedges

• Trimming grass and shrubs )

- when cutting long grass, work in stages from the top

and take small cuts

- for optimal cutting results, only cut dry grass

- keep the tool away from solid objects in order to

protect the cutting blades against excessive wear

- grass shear blade G can also be used for trimming

shrubs

Скачать «SKIL 0750 RA» — 8,93 МБ СкачатьСкачиваний: 0

Инструкция SKIL 0750 RA — страница 9

Другие руководства из этой категории