Инструкция SKIL 0750 RA — страница 10

Инструкция

PDF

8,93 МБ

152

Садовая техника

OlegTech20

Инструкция для SKIL 0750 RA на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

APPLICATIONADVICE

• For trimming a hedge at a uniform height level

- fasten a piece of string along the length of the hedge

at the desired height

- trim the hedge just above this string

• Recommended cutting/trimming times (Western Europe)

- trim hedges with deciduous leaves in June and

October

- trim evergreen hedges in April and August

- trim conifers and other fast-growing shrubs every 6

weeks from May until October

MAINTeNANCe / serVICe

• This tool is not intended for professional use

• Keep tool, charger and cutting blades clean

! unplugchargerfrompowersourcebefore

cleaning

! alwaysremovethebatterybeforecleaning

- clean the tool with a damp cloth (do not use cleaning

agents or solvents)

- clean ventilation slots J 2 regularly with a brush or

compressed air

- after use, always carefully clean and lightly lubricate

the cutting blades

! weargloveswhenhandlingorcleaningthe

cuttingblades

• Regularly check the condition of the cutting blades and

the tightness of the blade bolts

• Regularly check for worn or damaged components and

have them repaired/replaced when necessary

• Sharpening the cutting blades

! removebatteryfromtool

- remove cutting blades from tool before sharpening

- sharpen the cutting blades with a small and smooth

le, in case a solid object damaged them

- we advise you, however, to have the blades sharpened

by a specialist

- lubricate the cutting blades after sharpening

• Storage ¡

- store the tool indoors in a dry and locked-up place,

out of reach of children

- securely mount storage rail K on the wall with 4 screws

(notsupplied) and horizontally leveled

- use blade guards L 2 when storing the tool

- lubricate the cutting blades before storing the tool

• If the tool/charger should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool or charger undismantled together with

proof of purchase to your dealer or the nearest SKIL

service station (addresses as well as the service

diagram of the tool are listed on www.skil.com)

- in case of a defective charger send bothchargerand

battery to your dealer or the SKIL service station

TroUBlesHooTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! switchoffthetoolandremovethebatterybefore

investigatingtheproblem

★ Tool operates intermittently

- internal wiring defective -> contact dealer/service

station

- on/o switch defective -> contact dealer/service

station

★ Motor runs but blades remain stationary

- internal fault -> contact dealer/service station

★ Cutting blades hot

- cutting blades blunt -> have blades sharpened

- cutting blades have dents -> have blades inspected

- too much friction due to lack of lubricant -> lubricate

blades

eNVIroNMeNT

• Donotdisposeofelectrictools,batteries,

accessoriesandpackagingtogetherwithhousehold

wastematerial (only for EU countries)

- in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol @ will remind you of this when the need for

disposing occurs

• The nickel-metalhydride battery must be kept separate

from the natural environment and should not be disposed

of as normal domestic waste (symbol # will remind you

of this when the need for disposing occurs)

! priortodisposalprotectbatteryterminalswith

heavytapetopreventshort-circuit

- dispose of the batteries at an ocial collection point

for batteries

! batteriesmayexplodewhendisposedofinfire,

sodonotburnbatteryforanyreason

deClArATIoN oF CoNForMITY

• We declare under our sole responsibility that the product

described under “Technical data” is in conformity with the

following standards or standardization documents: EN

60335, EN 60745, EN 61000, EN 55014 in accordance

with the provisions of the directives 2006/95/EC,

2004/108/EC, 2006/42/EC, 2000/14/EC, 2011/65/EU

• Technicalfileat: SKIL Europe BV (PT-SEU/ENG1),

4825 BD Breda, NL

¹ÊÁÂÆÎ¹Æ¼½ÊÇÇ¾¼½Æ

È½Ê¹ÌÁÇÆËŵÆ¿ÁÆ½½ÊÁÆ¿

ÍÊÇÈ½Ɠˁ˅ʿ˂Ê½¼¹Ɠ

Ä¹¾ÁÂÃ¿Ê¹¹¾

ÈÈÊÇÎ¹Ä¹Æ¹¿½Ê

24.02.2014

NoIse/VIBrATIoN

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 58 dB(A) and the sound

power level 78 dB(A) (standard deviation: 3 dB), and the

Скачать «SKIL 0750 RA» — 8,93 МБ СкачатьСкачиваний: 0

Инструкция SKIL 0750 RA — страница 10

Другие руководства из этой категории