Инструкция по эксплуатации Saturn ST-VC7294 — страница 4

extended tube slightly to lock it in place

The tube can be extended to a maximum length of about 90cm.

4.Crevice Tool

Use this accessory tool for corners crevices and cracks.

5.Duster Brush

The Duster Brush (2 in 1) cleaner accessory is for removing dust from all type of surfaces such as lampshades electric equipment air conditioner grills car dashboards etc Separately it can be used as a sofa nozzle (Fig 8).

6.Water Brush & Liquid Suction

The Water Brush is so versatile that it can be used for vacuuming both solid and liquid dirt and is mainly for use on hard floor surface.

Caution: If you use your machine for liquid suction Make sure you first reduce the amount of water in the tank by about half

It is also important not to allow the tank to become too full of vacuumed liquid.

Before liquid suction you must change the carpet brush with the Water Brush

When you finish empty the tank completely and vacuum up about one liter of clean water to rinse clean the inside of the Flexible

Hose AND THE Telescopic Tube Repeat if necessary.

To dry the inside of Hose & the Tube detach the Water Brush and run your machine for a few minutes without sucking up any dirt Wash and dry the water brush separately Vacuum soapy liquid or detergent should be avoided as this causes frothing inside the water tank.

7.Automatic Cord Storage

Your system comes with an

Automatic Code Storage system Push the button at the back of the machine and the cord is retracted automatically The large button also allows this to be done with your foot (Fig 9).

Caution: While nearing the end of the retraction hold on to the end of the cord and guide it into the cord storage compartment

The force and speed of the retraction may cause the plug to snap back and hit something

Product Care and Storage

Always switch off the main switch and disconnect the AC cord from the electrical outlet before cleaning you machine or replacing any part 1 General

You may wipe the machine with a damp cloth Synthetic detergent may be used on plastic and metal parts if necessary Make sure you wipe the machine and its parts dry before storage.

Do not use strong cleaning agents such as benzene or thinner to clean the machine.

Always store your product and parts after they are completely dried.

2.Cleaning and Maintenance of the filter assembly.

It is highly recommended that you pour away the dirty water and clean the container and the filter assembly after each use

Keeping your home clean using a clean appliance is an advantage that the machine has over ‘bag’-vacuum cleaner.

To empty the water container push down the release button and hang up the water tank unit upwards remove from the vacuum unit (Fig 1).

Lift up and take out the cover and filter set from the water tank and empty the container Thoroughly clean rinse and leave to dry (Fig 2) (Fig 3).

Regularly dismantle and clean the filter assembly.

Remove the curved tube by pulling it from the meshed filter cage.

Pull out the filter cage and remove the sponge filter Wash and rinse all the components Dry before assembling them.

To remove stubborn dirt from the container and the filter assembly use normal washing-up liquid but make sure it is rinsed 7

thoroughly afterwards.

3.Air Outlet HEPA Filter

If there is a noticeable drop in the suction power this is an indication that the HEPA filter need to be cleaned or change a new one.

Take out the HEPA Filter Frame from the body (Fig 10).

Remove the HEPA Filter from the frame clean rinse by tap water and dry it before use again You can also replace it with a new one (Fig 11).

*** It is recommended to clean the

HEPA filter every 3 months at least or replace with a new one every one year at least.

4.Air Outlet Sponge Filter

Push the button on the Air Outlet Grill remove the Air Outlet Grill from the body (Fig 12).

Take out the Air Outlet Sponge Filter (Fig 13).

Clean it by water or replace it with a new one.

Caution: Use only original spare part.

5.Storage

Store your machine with care and in a cool dry place.

Troubleshooting

Do not disassemble or attempt to repair the machine yourself.

Conditions

Possible Cause and Solution

The machine stops during operation and all four suction power indicator lights start blinking together.

Wait for about 30 seconds before you operate the machine again This lets the machine reset whilst you identify one of the following possible causes.

The water has turned very dirt and milky Empty the water container and replace with clean water.

The water level is above the maximum level Reduce the water level.

The selected suction power level is too high for the current cleaning application Reduce the suction power.

The airflow is blocked Remove the blockage.

The machine does not start.

AC supply is not properly connected the AC cord to electrical supply.

Noticeable decrease in the suction power.

The HEPA filter requires replacement Change a new one.

There is a blockage Remove the cleaning tools and attachments from the machine and remove the blockage.

Leakage of water when using for cleaning of liquid waste.

The Switch Float is blocked Unblock it by cleaning.

Technical Data

Power Supply:

1600 W

Rated Voltage:

220-230 V

Rated Frequency:

50 Hz

Rated Current:

7.2 A

Vacuum cleaner

Instruction manual with warranty book

Package

ENVIRONMENT FRIENDLY DISPOSAL

You can help protect the environment!

Please remember to respect the local regulations: hand in the non-working electrical equipments to an appropriate waste disposal center

The manufacturer reserves the right to change the specification and design of goods