Инструкция по эксплуатации Saturn ST-CH7408 — страница 3

II Matters need attention for installation 1 Install surroundings (shown in figure 1)
Excessive windows and doors should be avoided around it when the Kitchen hood is Installed because when there are too many windows and doors the air convection is oversized which enable the lampblack rise to the 250mm effective attraction scope The efficiency of the kitchen hood comes under the influence 2

Ideal location for the installation (shown in figure 2)

The kitchen hood is installed over the cooker hood the range between the predestined affinity low end and the stove surface should be at least 650 mm Us scope is better to be in 650-

700mm 3 Requests for the installation of smoke pipe (shown in figure 3)
(1) The distance from the exit of the smoke pipe to the organism should not be too long Make the radius of turn as large as possible Make few curves or the effect will not be so good

(2) The exhaust duct should reach outdoor of the common smoke pipe and the connector must be narrow

Please don't discharge the waste gas into hot flue 4 Keeping the organism level (shown in figure 4)

After the installment watch out if it's horizontal to avoid the spillover of the oil caused by the oil cup being oblique 1 The waste gas should not be discharged into the hot flue which is used to discharged the smoke of burning gas or other kinds of fuel. 2 When boring holes avoid the power cords inside the wall so as not to get an electric shock (shown in figure5). 3 The electric outlet must be earth lead and the plug can't be changed optionally (shown in figure 6) 4 Proper space (usually about 10mm)
should be left on both sides of the organism when making the cabinet

The boards that cover the organism should be turnable so as to be convenient for maintenance and repair (shown in figure 7) 5

III Method of installation 1 Determining the location: install the kitchen hood horizontally above the stove The bottom of the range hood is about 650mm to 750mm high The size the with drawable boards we refer to you is 430mm which can be adjusted according to actual situation The open holes must be vertical centered and horizontal to the organism 2 Installing the cladding: first bore three holes in the dry wall whose diameters are 8mm and depths are 50mm to 60mm Then put the expansion tube into the holes At last use the lag wood screws of the size of

ST4х50 in the packing box to set the cladding 3 Adjusting the stretched tube (if there is): pull out the stretched tube remove the protective layer put it into the gap between the decorated tube and organism and adjust to the appropriate height. 4 Installing the organism (in figure 8): press and slide the pothook on the cladding into the holes at the back of the organism Rock the organism with the hand to see if it is fastened. 5 Fixing the exhaust duct: insert the exhaust duct between the inside track and the outside track of the air outlet set with ST3X6 bolt and put the other end outdoor. 6 Fixing the exhaust duct: insert the exhaust duct into the inside track of the check valve's air outlet set with ST3X6 tapping screw and connect the other end outdoor (the air outlet is at the top of the organism) 7 Fixing the other end of the exhaust duct (reference)
(1) When the exhaust duct and the charging floor are just against the window: remove a pane of glass and fix a veneer with a hole You can also make a hole on the glass. (2) When the charging floor is not near the window:
Choose the nearest charging floor and the window which can reach outdoor to fix the exhaust duct by going through the window; or choose the nearest charging floor and bore a hole in the wall then make the exhaust duct go through the wall. (3) Bore a hole in the wall:

Measure and draw a circle on the wall (the diameter is a little bigger than that of the exhaust duct) and bore a hole with long drill pay attention to the structure and metal of the wall

Don't destroy the wall surface beyond the hole The diameter of the hole should be close to the diameter of the exhaust duct or the smoke can not go out smoothly The noise will be too much and the wind rate will also reduce