Инструкция по эксплуатации Saturn ST-CC7136 — страница 3

More specifically:

DO NOT let children or untrained persons use the appliance without supervision.

NEVER immerse the iron cable or plug in any liquid.

DO NOT leave the hot iron touching fabrics or very inflammable surfaces.

NOT leave the appliance unnecessarily plugged in Disconnect the plug from the mains when the appliance is not being used.

NEVER touch the appliance with wet or damp hands.

DO NOT use the power cord or the appliance in order to pull the plug out of the socket.

DO NOT leave the appliance exposed to the weather (rain sun etc.).

DO NOT leave the iron without supervision when it is connected to the power supply.

DO NOT fill the reservoir with water before removing the plug from the socket.

PLEASE NOTE!

Do not use chemical additive scented substances or decalcifiers

Failure to comply with the abovementioned regulations leads to the loss of guarantee.

ANTI-CALC SYSTEM

A special resin filter inside the water reservoir softens the water and prevents scale build-up in the plate The resin filter is permanent and does not need replacing.

Please note:

Use tap water only Distilled and dematerialized water makes the “Zero-

Calc” anti-calc system ineffective by altering its physicochemical characteristics.

ANTI-DRIP SYSTEM

With the anti-drip system you can perfectly iron even the most delicate fabrics.

Always iron these fabrics at low temperatures The plate may cool down to the point where no more steam comes out but rather drops of boiling water that can leave marks or stains In these cases the Anti-drip system automatically activates to prevent vaporization so that you can iron the most delicate fabrics without risk of spoiling or staining them.

General Instructions

When using the iron for the first time you may notice a slight emission of smoke and hear some sounds made by the expanding plastics This is quite normal and it stops after a short time

We also recommend passing the iron over an ordinary cloth before using it for the first time.

PREPARATIONS

Soft the laundry to be ironed according to the international symbols on the garment label or if this is missing according to the type of fabric.

GARMENT

LABEL

FABRIC

TYPE

THERMOSTAT

REGULATION

synthetic

low temperature silk
wool

medium temperature cotton
linen

high temperature

Fabric not to be ironed

Start ironing the garments requiring a low temperature.

This reduces the waiting times (the iron takes less time to heat up than to cool down) and eliminates the risk of scorching the fabric.

STEAM IRONING

Filling the reservoir:

Check that the plug is disconnected from the socket. Move the steam knob 4 to “

” [Fig 5].

Open the cap.

Raise the tip of the iron to help the water enter the opening without overflowing [Fig 1].

Slowly pour the water into the reservoir using the special measure and taking care not to go over the maximum level (about 300 ml) indicated by “MAX” on the reservoir.

Close the cap 3.

Selecting the temperature

Put the iron in a vertical position.

Put the plug in the socket.

Adjust the temperature knob according to the international symbol on the garment label [Fig 3] The power light indicates that the iron is heating up Wait until the power light goes off before ironing.

Warning: during ironing the power light 8 comes on at intervals indicating that the selected temperature is maintained If you lower the selected temperature after ironing at a high temperature do not start ironing until the power light comes on again.

Selecting the steam

The quantity of steam is regulated by the steam knob.

Turn the steam knob to a position between minimum and maximum depending on the quantity of steam required and the temperature selected

[Fig 5].

Warning: the iron gives off steam continuously only if you hold the iron horizontally You can stop the continuous steam by placing the iron in a vertical position or by moving the steam knob to “

” As indicated on the steam knob and in the initial table you can only use steam at the highest temperatures If the selected temperature is too low water may drip onto the plate.

Selecting Shot-steam and steam when ironing vertically

Press the shot-steam button 5 to generate a powerful burst of steam that can penetrate the fabrics and smooth the most difficult and tough creases

Wait for a few seconds before pressing again [Fig 4].

By pressing the shot-steam button at intervals you can also iron vertically (curtains hung garments etc.) [Fig 6]

Warning: the shot-steam function can only be used at high temperatures Stop the emission when the power light 8 comes on than start ironing again only after the light has gone off.

DRY IRONING

To iron without steam follow the instructions in section “steam ironing” leaving the steam selector 4 on position “

SPRAY FUNCTION

Make sure that there is water in the reservoir Press the spray button F slowly (for a dense spray) or quickly (for a vaporized spray) [Fig 2].

Warning: for delicate fabrics we recommend moistening the fabric beforehand using the spray function or putting a damp cloth between the iron and the fabric To avoid staining do not use the spray on silk or synthetic fabrics.

AUTO STOP (automatic safety shutoff)

If the iron is left motionless for more than 30 seconds the heating element will be switch off automatically To indicate that the iron has shut off the

Auto stop pilot light (green) will start blinking and six sound signals will be audible.

In a horizontal position this will happen after 30 seconds.

In a vertical position this will happen after 8 minutes.

When picking up the iron again the

Auto stop pilot light will go out The supply pilot light will come on This indicates that the iron is heating up again.

Wait for the supply pilot light to go out Then you can recommence ironing.

SELF-CLEANING

The self-cleaning feature cleans inside the plate removing impurities We recommend using it every 10-15days

Directions:

Fill the reservoir up to the maximum level indicated and set the steam dial to “

Adjust the temperature knob 9 to the highest temperature and wait for the light (red) to turn off.

Pull the plug out of the socket and hold the iron horizontally over the sink.

Hold the calc-clean button 11 setting until all the boiling water steam impurities come out [Fig 7]

-When the soleplate has cooled down you can clean it with a damp cloth.

CLEANING

Please note: before cleaning the iron in any way make sure that the appliance plug is not connected to the socket.

Any deposits starch residue or size left on the plate can be removed using a damp cloth or an unabrasive liquid detergent.

Avoid scratching the plate with steel wool or metallic objects.

The plastic parts can be cleaned with a damp cloth then wiped over with a dry cloth.

HOW TO PUT IT AWAY

At the end of the using regulate the steam dial to “

”point.

When there is no steam regulate the temperature dial to “min” point

Disconnect the plug of the iron from the socket.

Empty the reservoir by turning the iron upside down and gently shaking it.

Leave the iron vertically to cool down 4