Инструкция по эксплуатации Saturn ST-CC7116 — страница 2

supervision or instruction concerning use of the appliance by a person responsible for their safety It is not advised to use this appliance by children under 14

Children should be supervised to ensure that they do not play with the appliance

SAVE THE INSTRUCTION MANUAL

FOR FUTURE REFERENCE.

Notes:

• Some parts of the iron have been slightly greased and as a result the iron may smoke slightly when switched on for the first time It will not happen again after a few uses.

• Before using for the first time remove any protective films or stickers from the sole plate Clean the sole plate with a soft cloth.

• When using the iron for the first time test it on an old piece of fabric to ensure that the sole plate and water tank are completely clean.

IRONING

Important Have you read the section

"Important Safeguards'?

CHOICE OF WATER

• This iron can be used with normal tap water.

• If the water in your area is particularly hard it is advisable to use distilled or demineralized water

• Do not use chemically descaled water or any other liquids for refilling

HOW TO FILL WITH WATER

• Set the Steam Control knob to "O" and the Temperature Control Dial to

“OFF”.

• Unplug the iron from the wall outlet and wait for the iron to cool down.

• Pour water into the water inlet (5).

Fill up to the maximum level "MAX" of the water tank

TEMPERATURE CONTROL SETTING

• Always check garment label for ironing instructions before ironing garment

• If the ironing instructions are missing then the table below may help you.

• First you should sort the laundry:

Wool with wool Cotton with cotton etc

Start ironing the fabrics requiring the lowest temperature and progress to the higher ones because the iron heats up quicker than it cools down.

• If the fabric consists of various kinds of fibres (e.g cotton with polyester) you must always select the ironing temperature for the material with the lowest advised temperature.

LABEL

KIND OF

TEXTILE

FIBRE

MATERIAL

Synthetic

Acrylic

Modacryc

Polypropylene

Po|yurethane

Synthetic

Acetate

Triacetate

Synthetic

Cupro

Polyamide (Nylon)

Polyester

Viscose (Rayon)

Silk

Silk

Wool

Wool

Cotton

Cotton

Linen

Linen

SETTING THE TEMPERATURE

• Insert the plug in the wall socket and stand the iron upright.

• Turn the temperature control knob (1) to the desired temperature setting.

• The desired temperature has been reached when the pilot light has turned off The pilot light will turn on and off from time to time indicating that the selected temperature is being maintained.

SPRAYING

This function can be used any time and does not affect the ironing temperature.

• Fill water into the iron.

• Aim the nozzle towards the garment.

• Press the Spray Button (3).

STEAM IRONING

This function can be used only at higher ironing temperatures for moderate steam ••* or MAX for maximum steam

• Fill water into the iron.

• Stand the iron upright.

• Connect the iron to a suitable mains supply outlet.

• Turn the temperature control (1) to the "•••"or MAX setting

• The pilot light turns off when the required temperature is reached The iron is ready for use.

• Turn the steam knob (7) to the required position steam starts coming 5

out from the holes in the sole plate

Notice:

With conventional steam ironing water may leak from the sole plate if too low a temperature has been selected If this happens turn the temperature control (1) to the advised position Steam will recommence as soon as the appropriate temperature has been reached.

BURST OF STEAM

This function provides an extra amount of steam to remove stubborn wrinkles.

• Fill the iron with water as described on page 3

• Turn the temperature control to the position "MAX'.

• The pilot light turns off when the required temperature is reached.

• The iron is ready for use.

• Press the Burst of Steam button (2) once.

• Steam will penetrate into the garment removing the wrinkles

• Wait a few seconds before pressing the steam control knob again when there are stubborn wrinkles.

DRY IRONING

• Connect the iron to a suitable mains supply outlet.

• Ensure that the steam control knob (7) is in position "O".

• Select the setting on the temperature control (1).

• When the pilot light turns off the required temperature is reached The iron is ready for use.

CARE AND CLEANING

1 Turn the Temperature Control Dial to

“OFF” then disconnect the iron from the wall outlet and let it cool down completely.

2 Deposits and other residues on the sole plate can be removed with a cloth soaked in a vinegar/water solution.

3 The casing may be wiped with a damp cloth and then polished with a dry one.

4 Never use any abrasives to clean the sole plate.

5 Keep the sole plate smooth; avoid contact with metal objects.

STORAGE

• Turn the temperature control (1) to

"•" and set the steam control knob (7) to position "O" (= no steam).

• Disconnect the iron from the wall outlet.

• Pour any remaining water out of the water tank.

• Stand the iron upright and let it cool down completely.

• The power cord can then be wound around the iron.

• Always store the iron in an upright position.

SAFETY PROTECTIVE CUT-OUT

In the unlikely event of the thermostat failing the protection cut-out will operate to prevent the iron overheating

Then the iron should be taken to the nearest authorized service facility.

Specifications

Power: 2200 W

Rated Voltage: 220-230 V

Rated Frequency:

50 Hz

Rated Current:

10 A

Iron

Instruction Manual with

Warranty Book 1

Package 1

ENVIRONMENT FRIENDLY

DISPOSAL

You can help protect the environment!

Please remember to respect the local regulations: hand in the non-working electrical equipments to an appropriate waste disposal centre.

The manufacturer reserves the right to change the design of the product.

УТЮГ

Уважаемый покупатель!

Поздравляем Вас с приобретением изделия с торговой маркой

“Saturn”

Уверены что наши изделия будут верными и надежными помощниками в

Вашем домашнем хозяйстве!

Не подвергайте устройство резким перепадам температур

Резкая смена температуры (например внесение устройства с мороза в теплое помещение) может вызвать конденсацию влаги внутри устройства и нарушить его работоспособность при включении Устройство должно