Инструкция по эксплуатации Saturn ST-CC7109 — страница 2

ANTI-CALC SYSTEM

A special resin filter inside the water reservoir softens the water and prevents scale build-up in the plate The resin filter is permanent and does not need replacing.

Please note:

Use tap water only Distilled and/demineralised water makes the anti-calc system ineffective by altering its physicochemical characteristics.

Do not use chemical additives scented substances or decalcifiers Failure to comply with the above-mentioned regulations leads to the loss of guarantee

ANTI-DRIP SYSTEM

With the anti-drip system you can perfectly iron even the most delicate fabrics.

Always iron these fabrics at low temperatures The plate may cool down to the point where no more steam comes out but rather drops of boiling water that can leave marks or stains In these cases the Anti-drip system automatically activates to prevent vaporization so that you can iron the most delicate fabrics without risk of spoiling or staining them.

G E N E R A L I N S T R U C T I O N S

When using the iron for the first time you may notice a slight emission of smoke and hear some sounds made by the expanding plastics This is quite normal and it stops after a short time

We also recommend passing the iron over an ordinary cloth before using it for the first time.

PREPARATIONS

Soft the laundry to be ironed according to the international symbols on the garment label or if this is missing according to the type of fabric.

GARMENT

LABEL

FABRIC TYPE

THERMOSTAT REGULATION

synthetic

low temperature silk
wool

medium temperature

Cotton
linen

high temperature

Fabric not to be ironed

Start ironing the garments requiring a low temperature.

This reduces the waiting times (the iron takes less time to heat up than to cool down) and eliminates the risk of scorching the fabric.

STEAM IRONING

Filling the reservoir

Check that the plug is disconnected from the socket.

Move the steam selector (3) to “0”

[Fig 1].

Open the lid (2).

Raise the tip of the iron to help the water enter the opening without overflowing.

Slowly pour the water into the reservoir using the special measure (15) and taking care not to go over the maximum level (about 300ml) indicated by “MAX” on the reservoir [Fig 2].

Close the lid (2).

SELECTING THE TEMPERATURE.

Put the iron in a vertical position.

Put the plug in the socket.

Adjust the thermostat knob (10) according to the international symbol on the garment label [Fig 3] The plate temperature control light (9) indicates that the iron is heating up Wait until the plate temperature control light goes off before ironing.

Warning: during ironing the plate temperature control light (9) comes on at intervals indicating that the selected temperature is maintained If you lower the thermostat temperature after ironing at a high temperature do not start ironing until the plate temperature control light comes on again.

SELECTING THE STEAM.

The quantity of steam is regulated by the steam selector (3).

Move the steam selector to a position between minimum and maximum de-

pending on the quantity of steam required and the temperature selected

[Fig 1].

Warning: the iron gives off steam continuously only if you hold the iron horizontally You can stop the continuous steam by placing the iron in a vertical position or by moving the steam selector to “0” As indicated on the thermostat knob (11) and in the initial table you can only use steam at the highest temperatures

If the selected temperature is too low water may drip onto the plate.

SELECTING SHOT-STEAM AND

STEAM WHEN IRONING VERTICAL-

Press the shot-steam button (5) to generate a powerful burst of steam that can penetrate the fabrics and smooth the most difficult and tough creases Wait for a few seconds before pressing again

[Fig 4].

By pressing the shot-steam button at intervals you can also iron vertically (curtains hung garments etc.) [Fig 5]

Warning: the shot-steam function can only be used at high temperatures Stop the emission when the plate temperature control light (9) comes on than start ironing again only after the light has gone off.

DRY IRONING

To iron without steam follow the instructions in section “steam ironing” leaving the steam selector (3) on position “0”.

SPRAY FUNCTION

Make sure that there is water in the reservoir Press the spray button (4) slowly (for a dense spray) or quickly (for a vaporized spray) [Fig 6].

Warning: for delicate fabrics we recommend moistening the fabric beforehand using the spray function (4) or putting a damp cloth between the iron and the fabric To avoid staining do not use the spray on silk or synthetic fabrics.

CLEANING

Please note: before cleaning the iron in any way make sure that the appliance plug is not connected to the socket

Any deposits starch residue or size left on the plate can be removed using a damp cloth or an unabrasive liquid detergent.

Avoid scratching the plate with steel wool or metallic objects.

The plastic parts can be cleaned with a damp cloth then wiped over with a dry cloth.

SELF-CLEANING

The self-cleaning feature cleans inside the plate removing impurities We recommend using it every 10-15days Directions:

-Fill the reservoir up to the maximum level indicated and set the steam selector

-Set the thermostat knob (11) to the maximum temperature and wait for the light (6) to turn off

-Pull the plug out of the socket and hold the iron horizontally over the sink

-Hold the cleanout button (12) setting until all the boiling water steam impurities come out [Fig 7]

-When the soleplate has cooled down you can clean it with a damp cloth.

HOW TO PUT IT AWAY

Disconnect the plug of the iron from the socket.

Empty the reservoir by turning the iron upside down and gently shaking it

Leave the iron to cool down completely.

Roll up the power cord with the rewinder [Fig 8].

Always put the iron away in a vertical position.

ADVICE FOR GOOD IRONING

We recommend using the lowest temperatures with fabrics that have unusual finishes (sequins embroidery flush etc.).

If the fabric is mixed (e.g 40% cotton 60% synthetics) set the thermostat to the temperature of the fibre requiring the lower temperature.

If you don’t know the composition of the fabric determine the suitable temperature by testing on a hidden corner of the garment Start with a low temperature and increase it gradually until it reaches the ideal temperature.

Never iron areas with traces of perspiration or other marks: the heat of the plate fixes the stains on the fabric making them irremovable.

The size is more effective if you use a dry iron at a moderate temperature: excess heat scorches it with the risk of forming a yellow mark.

To avoid marking silk woolen or synthetic garments shiny iron them inside out

To avoid marking velvet garments shiny iron in one direction (following the fibre) and do not press down on the iron.

The heavier the washing machine is loaded the more garments come out