Инструкция по эксплуатации Saturn ST-CC0213 — страница 3

· Connect he iron to a suitable mains supply outlet

· Turn the temperature control button to the “• • ” or “• • •” "MAX" setting

· The pilot light turns on when the required temperature is reached The iron is ready for use.

· Turn the steam knob to the required position steam starts coming out from the holes in the sole plate.

· Notice: With conventional steam ironing water may leak from the sole plate if too low temperature has been select If this happens turn the temperature control to the advised position Steam will recommence as soon as die appropriate temperature has been reached.

BURST OF STEAM

This function provides an extra amount of steam to remove stubborn wrinkles.

· Fill the iron with water.

· Turn the temperature control to the position 'MAX".

· The iron is ready for use.

· Press the burst of steam knob once

· Steam will penetrate into the garment removing the wrinkles.

· Wait a few seconds before pressing the steam control knob wrinkles again when there are stubborn wrinkles.

· Usually all wrinkles can be removed within three pressings.

DRY IRONING

· Connect the iron to a suitable mains supply outlet.

· Ensure that the steam control knob is in position “0”.

· Select the setting on the temperature control.

· When the pilot light turns off the required temperature is reached The iron is ready to use.

TO LET THE IRON HEAT UP AGAIN

Pick up the iron or move it slightly.

The red shot-off pilot goes out If the temperature of the soleplate drops below the set ironing temperature the temperature pilot goes on.

If the pilot light goes on after you have move the iron wait for it to go out before you start ironing.

If the pilot light does not go on after you move the iron the soleplate still has right temperature and iron is ready for use.

SELF CLEAN FUNCTION

The Self Clean function can remove any scale or impurities.

Use the self-clean function once every two weeks If the water in your area is very hard the self-clean function should used more frequently.

· Make sure the appliance is unplugged.

· Set the Variable steam control knob to position "0" (=no steam).

· Fill the water tank to the maximum level.

· Select the maximum ironing temperature.

· Put the plug in the wall socket.

· Unplug the iron when the temperature pilot light has gone out.

· Hold the iron over the silk press and hold die self-clean button and gently shake the iron.

· (Steam and boiling water will come out of the soleplate Impurities and flakes (if any) will be flushed out.)

· Release the self-clean button as soon as all water in the tank has been used up.

· Repeat the self-clean process if the iron still contains a lot of impurities.

CARE AND CLEANING

1.Turn the Temperature Control Dial to OFF then disconnect the iron from the wall outlet and cool it down completely.

2.Deposits and other residues on the sole plate can be removed with a cloth soaked in a vinegar/water solution.

3.The casing may the wiped with a damp cloth and then polished with a dry one.

4.Never use any abrasives to clean the sole plate.

5.Keep the sole plate smooth avoid contact with metal objects.

6.When you have finished ironing or you are leaving iron unattended:

turn the steam control knob to position “0”

stand the iron upright

disconnect the iron from the wall outlet.

Do not allow children to touch the iron or the power cord whom ironing.

7.Do not immerse die iron or the cord into water or any other liquid.

8 Do not touch hot metal parts hot water or steam These parts become hot and may cause burns Take care if you turn die iron upside downs: there may be not hot water in the tank The plug and cord should not be allowed to touch the hot sole plate Let the iron cool down completely before taking it away

Roll the power cord around the iron for storage.

9.Disconnect die iron from the wall outlet for filling in water or when you remove the water after use.

10 The iron is for household use only.

12 Save the instruction manual for future reference

Notes:

· Some parts of the iron have been slightly greased and as result the iron may smoke slightly when switched on for the first time It will not happen again after a few uses.

· Before using for the first time remove any protective films or stickers from the sole plate and the cabinet Then clean the sole place with a soft cloth.

· When using the iron for the first time test it on an old piece of fabric to ensure that the sole plate and water tank are completely clean.

CHOICE OF WATER

· This iron can be used with normal tap water.

· If the water in your area is particularly hard it is advisable to use distilled or demineralized water.

· Do not use chemically descaled water or any other liquids for refilling.

HOW TO FILL IN WATER

· Set the Steam Control Knob “0” and the temperature Control Dial to OFF.

· Unplug the iron from the wall outlet.

· Pour water into the water inlet.

· Fill up to the maximum level “MAX” of the water tank.

LABEL

KIND OF

TEXTILE

FIBRE

MATERIAL

Synthetic

Acrylic

Modacryc

Polypropylene

Po|yurethane

Synthetic

Acetate

Triacetate

Synthetic

Cupro

Polyamide (Nylon)

Polyester

Viscose (Rayon)

Silk

Silk

Wool

Wool

Cotton

Cotton

Linen

Linen

SETTING THE TEMPERATURE

· Insert the plug in the wall socket and stand the iron upright.

· Turn the temperature control knob to the desired temperature setting.

· The desired temperature has been reached when the pilot light has turned off.

· The pilot light will turn on and off from time after time indicating that the selected temperature is being maintained.

Specification

Power: 2200 W

Working voltage: 220-230 V

Working frequency: 50 Hz

Rated сurrent 10 A

Iron 1pc

Instruction manual with warranty book 1pc

Package 1pc

ENVIRONMENT

FRIENDLY DISPOSAL

You can help protect the environment!

Please remember to respect the local regulations: hand in the non-working electrical equipments to an appropriate waste disposal centre.

The manufacturer reserves the right to change the specification and design of goods.