Инструкция REMS 174012 — страница 9

Инструкция

PDF

3,44 МБ

108

Инструменты / Контрольно-измерительные приборы

IvanMaster

Инструкция для REMS 174012 на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

eng eng

Serrated cross-blade borer 22/45 172291

Serrated cross-blade borer 22/65 172293

Serrated cross-blade borer 32/45 174291

Serrated cross-blade borer 32/65 174293

Serrated cross-blade borer 32/90 174295

Serrated cross-blade borer 32/115 174296

Forked cutter 16 171305

Cross-forked cutter 16 171306

Serrated forked cutter 22/65 172305

Serrated forked cutter 32/65 174305

Serrated forked cutter 32/90 174306

Root cutter 22/65 172310

Root cutter 32/65 174310

Root cutter 32/90 174311

 Chainail16,smoothrings  171340

 Chainail16,spikedlinks  171341

 Chainail22,smoothrings  172340

 Chainail22,spikedlinks  172341

 Chainail32,smoothrings  174340

 Chainail32,spikedlinks  174341

REMS CleanM 140119

1.3. Working range

REMS Cobra 22

Cable Ø 8 mm (max. working length 10 m) Pipe Ø 10 – 50 (75) mm

Cable Ø 16 mm (max. working length 40 m) Pipe Ø 20 – 100 mm

Cable Ø 22 mm (max. working length 70 m) Pipe Ø 30 – 150 mm

REMS Cobra 32

Cable Ø 8 mm (max. working length 10 m) Pipe Ø 10 – 50 (75) mm

Cable Ø 16 mm (max. working length 40 m) Pipe Ø 20 – 100 mm

Cable Ø 22 mm (max. working length 100 m) Pipe Ø 30 – 150 mm

Cable Ø 32 mm (max. working length 70 m) Pipe Ø 40 – 250 mm

1.4. Working speed REMS Cobra 22 REMS Cobra 22

 Workingspindle 740min־¹ 520min־¹

1.5. Electrical data

Rated voltage 230 V~; 50 Hz 230 V~; 50 Hz

Power input 750 W 1050 W

Rated current 3.3 A 5.8 A

Intermittent service S3 40% 4/10 min S3 40% 4/10 min

Protection class IP 34 F IP 44 F

1.6. Dimensions (L × W × H)

Drive unit 535 × 225 × 535 mm 535 × 225 × 595 mm

21” × 8.9” × 21” 21” × 8.9” × 23.4”

1.7. Weights

REMS Cobra 22 drive unit 19.1 kg (42.2 lb)

REMS Cobra 32 drive unit 24.6 kg (54.6 lb)

Tool set 16 1.8 kg (4.0 lb)

Tool set 22 2.3 kg (5.1 lb)

Tool set 32 1.9 kg (4.2 lb)

Cable set 5 × 16 × 2.3 m in cable carrier 7.4 kg (16.4 lb)

Cable set 5 × 22 × 4.5 m in cable carrier 20.6 kg (45.7 lb)

Cable set 4 × 32 × 4.5 m in cable carrier 26.3 kg (58.4 lb)

1.8. Noise information REMS Cobra 22 REMS Cobra 22

Emission at workplace 75 dB (A) 75 dB (A)

1.9. Vibrations

Weighted effective value

of acceleration 2.5 m/s² 2.5 m/s²

The indicated weighted effective value of acceleration has been measured

against standard test procedures and can be used by way of comparison with

another device. The indicated weighted effective value of acceleration can also

be used as a preliminary evaluation of the exposure.

CAUTION

The indicated weighted effective value of acceleration can differ during operation

from the indicated value, dependent on the manner in which the device is used.

Dependent upon the actual conditions of use (periodic duty) it may be necessary

to establish safety precautions for the protection of the operator.

2. Start-up

2.1. Electrical connection

WARNING

Caution: Mains voltage present! Before connecting the electric pipe and drain

cleaning machine, check whether the voltage given on the rating plate corre

spondstothemainsvoltage.Onbuildingsites,inawetenvironment,indoors

and outdoors or under similar installation conditions, only operate the electric

pipe and drain cleaning machine on the mains with a fault current protected

switch (FI breaker) which interrupts the power supply as soon as the leakage

current to earth exceeds 30 mA for 30 ms. When using an extension lead, pay

attention to the cable cross section necessary for the power of the electric pipe

and drain cleaning machine. The extension lead must be approved for the

specicationsin1.5.Electricaldata.

2.2. Handling and selection of the pipe and drain cleaning cable

The REMS Cobra machines use lengths of cable which can be connected up

as necessary. The REMS Cobra 22 machine comes either with the cable and

tool set 16 or 22 or both. The REMS Cobra 32 machine comes either with the

cable and tool set 22 or 32 or both. The pipe and drain cleaning cables can

eachbeusedwithoutmodicationstothemachine.

For the REMS Cobra 32 machine, the cable and tool set 16 can also be used

when using other clamping jaws 16 (accessories). To do this, remove the guard

(2). Push in the spring sleeve until it touches using a screwdriver. Push the

whole clamping jaw forward and lift out backwards over the parallel pin. Fit

clamping jaw 16 (set). To do this, push the clamping jaw 16 into the system

bearer, push in the spring sleeve until it touches and push the clamping jaw

over the parallel pin.

 Thepipeanddraincleaningcablesarespeciallyhardenedandhighlyexible.

They can be extended or shortened very quickly by T-groove safety connectors.

Push the T-bar (7) sideways into the T-groove (8) to do this. The spring-loaded

thrust pin on the bar side locks the two halves together. To separate them, push

back the spring-loaded thrust pin with the cable joint separator (9) and push

the T-bar out of the T-groove. The pipe and drain cleaning cables and pipe and

draincleaningtoolswillalsotothermakesofdraincleaningmachines.An

adapter drum with a cable Ø 8 mm, length 7.5 m is available as an accessory

for every REMS Cobra 22 and REMS Cobra 32 (see 3.4.).

NOTICE

Do not use pipe and drain cleaning cables with a damaged spring-loaded thrust

pin. The T-bar coupling may not be pushed by hand without cable joint separator

(9) out of the T-groove coupling (8) after locking. The joint could otherwise be

pulled apart during the cleaning process in the pipe by twisting of the pipe and

drain cleaning cable and the pipe and drain cleaning tool. The pipe and drain

cleaning cable and/or pipe and drain cleaning tool then stay in the pipe.

The size of the cable required depends on the diameter of the pipe to be

cleaned. See 1.3 for guidance.

The type of cable to be selected depends on the length and position of the

pipe to be cleaned as well as on the type of obstruction expected. The standard

pipe and drain cleaning cable is used for universal pipe and drain cleaning

operations.Beinghighlyexible,itisparticularlysuitablefordealingwithtight

bends or several bends in succession. For obstructions presenting particular

problems, e.g. when it is necessary to slice through roots, the pipe and drain

cleaning cable S with thicker cable wire (accessory) is to be recommended. A

weather and temperature-resistant plastic core is incorporated into the pipe

and drain cleaning cable with core (accessory) which prevents dirt from collecting

insidethecableorlongbresfromlodginginthespirals.

2.3. Selection of suitable pipe and drain cleaning tool

2.3.1. Straight auger

Used as the starting tool to withdraw a sample from which the cause of the

obstruction can be determined. Also to clear a solid blockage caused by textiles,

paper,kitchenwasteetc.topermittheowofwater.

2.3.2. Bulbous auger

 Usedforminorobstructionscausedbytextilesorpaper,duetoitshighexibility.

The extended club-head facilitates advancement in tight bends.

2.3.3. Funnel auger

Used for textile and paper obstructions in particular. Is especially useful for

larger diameter pipes due to its generous radius of action. Can also be used

as a recovery tool for cables left in the pipe.

2.3.4. Retrieving auger

Use for retrieving pipe and drain cleaning cables left in the pipe. With extended,

specially angled grappling arm. Not suitable for boring operations.

2.3.5. Serrated blade borer

Used to bore out greasy or heavily silted pipes. The tool is riveted to the

connector (not soldered or welded) so as to prevent any deformation of the

hardened spring steel blades.

2.3.6. Serrated cross-blade borer

Multi-purpose tool for obstructions of all kinds, including incrustations (e.g.

limescale deposits on the inside of the pipe). The tool is riveted to the connector

(not soldered or welded) so as to prevent any deformation of the hardened spring

steel blades. Recommended for use with pipe and drain cleaning cables S.

2.3.7. Forked cutter

Size 16 with one blade as a forked cutter, with two blades as a cross-forked

cutter, made of hardened spring steel to remove moderate to severe silting or

persistent grease contamination. Size 22 and 32 with serrated, replaceable

blade as a serrated forked cutter, made of hardened spring steel, and with

multiple uses, e.g. for clearing silting or to reduce (break down) root infestation.

2.3.8. Root cutter

Tool with hardened, replaceable ring-type saw, cutting to the front and rear.

Specially designed for root infested pipes. Recommended for use with pipe

and drain cleaning cables S.

2.3.9. Chain ail

The most important tool of all for the removal of greasy deposits and incrusta

tions(e.g.limescaledepositsontheinsideofthepipe).Chainailswithsmooth

ringsforbreakablepipes,e.g.plastic.Chainailswithspikedlinksforcastiron

or concrete pipes.

Скачать «REMS 174012» — 3,44 МБ СкачатьСкачиваний: 0

Инструкция REMS 174012 — страница 9

Другие руководства из этой категории