Инструкция REMS 174012 — страница 10

Инструкция

PDF

3,44 МБ

108

Инструменты / Контрольно-измерительные приборы

IvanMaster

Инструкция для REMS 174012 на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

eng eng

3. Operation

3.1. Investigation/removal of the obstruction

Position the electric pipe and drain cleaning machine 30 – 50 cm in front of the

opening of the pipe to be cleaned.

Check to ensure that the guard (2) has been installed on the chuck mount

together with the guide hose (1) for the cable. Install if necessary!

The guide hose prevents the cable from twisting if the tool becomes blocked,

as well as cushioning its vibrations and collecting any dirt it may have picked

up.

Feed a length of cable (5) into the electric pipe and drain cleaning machine

with the T-groove connector (8) leading until approximately 50 cm of the cable

length is protruding from the machine. Never connect more than one length of

cable cable at a time. Connect the pipe and drain cleaning tool (6) to the free

end of the pipe and drain cleaning cable, i.e. push sideways into the T-groove

ofthecableuntilitlockshome.Usethestraightaugerasthersttool.Introduce

the tool and cable into the pipe. Switch the electric pipe and drain cleaning

machine to rotate clockwise (switch position (“1”) at the switch (3). Draw the

pipe and drain cleaning cable manually out of the electric pipe and drain cleaning

machine and push it into the pipe to be cleaned until it develops a bend.

WARNING

Wear a suitable guide glove!

With the other hand, press down hard on the carrying handle (4) until the pipe

and drain cleaning cable (5) rotates. Spring force applied to the cable produces

the necessary thrust. When the bend has straightened, pull the carrying handle

(4) upwards. The pipe and drain cleaning cable immediately comes to a stand-

still. Feed in the pipe and drain cleaning cable again manually until a bend

develops.Thenapplyrmpressuretothecarryinghandle(4)againuntilthe

bend straightens. Keep repeating the procedure. Connect up further lengths

of cable as necessary until it reaches the obstruction and clears it.

When it reaches the obstruction (resistance), it is important that the pipe and

drain cleaning cable (5) is advanced with care (one centimetre at a time) . If

the pipe and drain cleaning cable seizes, the carrying handle (4) must be pulled

up immediately because the cable could otherwise break.

However, if a pipe and drain cleaning tool (6) has become blocked by an

obstruction, it should be freed by repeated, brief reversal of the direction of

rotation of the electric pipe and drain cleaning machine to anticlockwise (switch

position “R”) and clockwise (switch position “1”). Use the anticlockwise setting

only for this process. All other operations including the recovery of the cable

are carried out in clockwise direction.

3.2. Recovering the pipe and drain cleaning cable

Recovery of the pipe and drain cleaning cable (5) also takes place in clockwise

direction. Withdraw the rotating pipe and drain cleaning cable from the pipe

until it develops a bend. Release the pressure from the carrying handle (4) and

push the pipe and drain cleaning cable back into the electric pipe and drain

cleaning machine. Press the handle again and draw the pipe and drain cleaning

cable out of the pipe until it has developed a bend again. Keep repeating the

procedure until a length of cable has been pushed completely into the electric

pipe and drain cleaning machine or guide hose and it can be disconnected

from the following length of cable. Remove disconnected lengths of cable from

the pipe and drain cleaning machine and guide hose. Repeat this process until

the entire length of cable has been removed from the pipe.

3.3. Cleaning the pipe

From an examination of the contamination affecting the withdrawn straight

auger, it is generally possible to form conclusions as to the cause of the

obstruction and therefore to select a suitable tool (see 2.3) with which the entire

cross section of the pipe can then be completely cleaned.

3.4. Adapter drum with 8 mm pipe and drain cleaning cable (accessory)

Remove the guard (2) and guide hose (1). Fit the adapter drum (Fig. 3) (10)

with the Ø 8 mm pipe and drain cleaning cable in their place. The adapter drum

contains a clamping jaw set for the Ø 8 mm pipe and drain cleaning cable. The

operating procedure with this pipe and drain cleaning cable is the same as with

the Ø 16, 22 and 32.pipe and drain cleaning cables.

4. Maintenance

WARNING

Pull out the mains plug before carrying out maintenance or repair work!

Thisworkmayonlybeperformedbyqualiedpersonnel.

4.1. Maintenance

REMS Cobra is maintenance-free. The bearings of the drive shaft run iln a

permanent grease bearing. The machine therefore requires no lubrication.

Clean the REMS Cobra, pipe and drain cleaning cables and pipe and drain

cleaning tools after every use, especially also the clamping jaws and the area

around the clamping jaws.. Also clean the T-bar (7) and T-groove (8) connectors

of the pipe and drain cleaning cables (5) and pipe and drain cleaning tools (6).

Clean the spring-loaded thrust pin of the T-bar (7) connector and check correct

function. Clean heavily soiled metal parts with the REMS CleanM (Art. No.

140119) cleaner, for example, and then protect against rust. Clean plastic parts

(e.g. housing) only with the REMS CleanM machine cleaner (Art. No. 140119)

or a mild soap and a damp cloth. Do not use household cleaners These often

contain chemicals which can damage the plastic parts. Never use petrol,

turpentine, thinner or similar products to clean plastic parts. Make sure that

liquids never get inside the electric pipe and drain cleaning machine. Never

immerse the electric pipe and drain cleaning machine in liquid.

4.2. Inspection / maintenance

 Thisworkmayonlybecarriedoutbyqualiedpersonnelandwithoriginalspare

parts.

5. Faults

5.1. Fault: Electric pipe and drain cleaning machine not working.

Cause: Remedy:

●

Mains lead defective.

●

 HavethemainsleadchangedbyqualiedpersonneloranauthorisedREMS

customer service workshop.

●

Electric pipe and drain cleaning machine defective.

●

Have the pipe cleaning machine inspected/repaired by an authorised REMS

customer service workshop.

5.2. Fault: Pipe and drain cleaning cable (5) does not rotate despite pressed carrying handle (4).

Cause: Remedy:

●

Tool got stuck at an obstruction.

●

Work the pipe and drain cleaning tool free by repeatedly switching the direction

ofrotationbrieyfromanticlockwise(switchposition"R")toclockwise(switch

position"1")attheswitch(3).

●

Clamping jaws defective.

●

Change the clamping jaws (see 2.2) or have them changed by an authorised

REMS customer service workshop.

5.3. Fault: Pipe and drain cleaning cable (5) and/or pipe and drain cleaning tool (6) stays in the pipe.

Cause: Remedy:

●

Connector was not closed.

●

Check that the connector is tight after locking before use. Use a retrieving

auger to retrieve pipe and drain cleaning cable(s) (5) and/or pipe and drain

cleaning tools (6) left in the pipe.

●

Spring-loaded thrust pin of the pipe and drain cleaning cable (5) of the T-bar

connector (7) defective.

●

Change the pipe and drain cleaning cable.

●

Bore for locking the spring-loaded thrust pin of the T-groove connector (8)

soiled/damaged.

●

Clean bore or change pipe and drain cleaning cable (5) and/or pipe and drain

cleaning tool (6).

●

pipe and drain cleaning cable (5) broken.

●

Use retrieving auger to retrieve pipe and drain cleaning cable(s) (5) and/or pipe

and drain cleaning tools left in the pipe. Do not continue using broken pipe and

drain cleaning cables.

Скачать «REMS 174012» — 3,44 МБ СкачатьСкачиваний: 0

Инструкция REMS 174012 — страница 10

Другие руководства из этой категории