Инструкция DEWALT DW 343 K — страница 11

Инструкция

PDF

2,16 МБ

Инструменты / Контрольно-измерительные приборы

SofiaPro49

Инструкция для DEWALT DW 343 K на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

ENGLISH

DW343/DW343K

Switching on: slide the on/off switch (1) to the

front.

Switching off: slide the on/off switch to the rear.

Always switch off the tool when work is ì nished

and before unplugging.

Setting the electronic sawing speed (ì g. F1 & F2)

DW341/DW341K (ì g. F1)

The sawing speed varies with the pressure exerted

on the on/off switch (1).

To preset the sawing speed, turn the control dial

(3) to the desired level. The higher the rate, the

higher the sawing speed. The required setting

depends on the thickness and kind of material.

Use high speeds for sawing soft materials such

as wood. Use low speeds for sawing metal.

DW343/DW343K (ì g. F2)

The speed control dial (3) can be used for advance

setting of the required range of speed.

Turn the electronic speed control dial to the

required level. The required setting depends on

the thickness and kind of material.

Use high speeds for sawing soft materials such

as wood. Use low speeds for sawing metal.

After using the tool for an extended period

on low speed settings, run it for approx.

3 minutes on maximum no-load speed.

Holding the tool (ì g. G1 & G2)

Hold the tool as shown.

- DW341/DW341K: ì g. G1

- DW343/DW343K: ì g. G2

Sawing in wood

If necessary, draw a cutting line.

Switch the tool on.

Hold the tool against the workpiece and follow

the line.

For sawing parallel to the edge of your workpiece,

install the parallel fence (optional) and guide your

jigsaw along the workpiece a shown in ì gure H.

Sawing in wood using a pilot hole

If necessary, draw a cutting line.

Drill a hole ( min. 12 mm) and introduce the

saw blade.

Switch the tool on.

Follow the line.

For cutting perfectly round shapes, install the

trammel bar (optional) and set it to the required

radius (ì g. l).

Sawing up to a projecting edge (ì g. A & J)

Using a conventional blade, cut up to the

projected edge.

Finish off the cut using a î ush cutting blade.

Dust extraction (ì g. E)

When the tool is used indoor for extended

periods of time, use a suitable dust extractor

designed in compliance with the applicable

Directives regarding dust emission.

Sawing in metal

Mount an appropriate saw blade.

Proceed as described above.

•

Use a cooling lubricant (cutting oil) to

prevent overheating of the saw blade or

the workpiece.

Maintenance

Your D E WALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular

cleaning.

Lubricating the guide roller (fig. B)

• Apply a drop of oil to the guide roller (8) at regular

intervals to prevent jamming.

Cleaning

Keep the ventilation slots clear and regularly clean

the housing with a soft cloth.

Скачать «DEWALT DW 343 K» — 2,16 МБ СкачатьСкачиваний: 0

Инструкция DEWALT DW 343 K — страница 11

Другие руководства из этой категории