Инструкция BEHRINGER VIRTUAL AMPLIFICATION V-AMP PRO — страница 5

Инструкция

PDF

1,97 МБ

Звуковое оборудование

МилаBook58

Инструкция для BEHRINGER VIRTUAL AMPLIFICATION V-AMP PRO на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

V-AMP PRO

Fig. 2.2: V-AMP PRO front panel (section 2)

These five keys are for selecting a preset (A - E) within

one bank.

In EDIT mode (activated by simultaneously pressing the

arrow keys described in ), the keys perform the

function printed directly above them. As long as EDIT mode

is active, the EDIT MODE LED lights up.

s A: Accesses the MIDI functions. Use the arrow keys to

set the MIDI channels for transmitting and receiving

(1 through 16).

If you use key A in EDIT mode to select the MIDI function

and then press the TAP key, the MIDI OUT jack is set to act

as a MIDI THRU. In this case, the V-AMP PRO does not

send its own MIDI information, but passes on the signal

received at the MIDI IN jack.

s B: Selects the DRIVE function. This noticeably raises

distortion and volume. Use the arrow keys to switch DRIVE

on and off. The DRIVE function is wired pre GAIN control.

+ While editing the DRIVE function, you can also

activate and adjust the wah-wah effect by turning

the EFFECTS control. The LEDs surrounding the

EFFECTS control indicate the position of the pedal.

If none of the LEDs lights up, the wah-wah is

bypassed.

s C: This key activates the CABINETS mode. Use the arrow

keys to select the type of speaker or combination of

speakers you want. You can also switch off the speaker

simulation completely (-). For further details, please refer

to chapter 5.2 Speaker descriptions.

s D: Use this key to select the REVERB function. The

arrow keys can be used to select one of nine different

types of reverb in addition to the multi-effects processor.

For further details see chapter 6.2.

s E: Here you can activate the NOISE GATE function. Use

the arrow keys to adjust the noise reduction threshold.

+ After preset editing, please press TUNER/EXIT to

quit (the EDIT MODE LED dies out).

+ DIGITAL OUT: The digital output can be configured if

keys A and B are pressed simultaneously. The

display reads either SP for S/PDIF or AE for

AES/EBU. Please switch between these two formats

using the TAP key. The LEDs in the display illustrate,

whether you have chosen internal synchronization

(with 44.1, 48 or 96 kHz sample rate) or external

synchronization via word clock (see tab. 2.1 in this

users manual). Use the arrow keys to select the

appropriate sample rate with respect to the

receiving device. The TUNER/EXIT key allows you to

quit the DIGITAL OUT configuration.

2. CONTROL ELEMENTS

+ CONFIGURATION: If you press the D and E keys

simultaneously, you can select the V-AMP PROs

general operating mode allowing adjustments to

different studio and live situations (see chapter 3).

Press TUNER/EXIT to quit configuration.

The TUNER button is for switching on the tuner. In addition,

this button can be used to quit EDIT mode (Exit).

Use the two arrow keys to select a different bank (BANK

DOWN and BANK UP). You can skip banks by holding

each of the keys down. To activate the EDIT mode, press

both keys simultaneously (THE EDIT MODE LED in the

display lights up). if you press one of the keys A - E ( )

in that mode, the arrow keys can be used for setting

parameters.

The TAP button performs five functions:

s Tap: Tap the rhythm of a piece of music on the TAP

button and the selected effect automatically adapts to the

tempo of the music.

s Presence: Holding down the TAP button, you can use

the TREBLE control to change the PRESENCE setting of

the amp simulation model youve selected.

s 2

parameter: You also can access the second effects

parameter set by the EFFECT control by holding down the

TAP button (see chapter 6).

s Amp models 17 - 32: Keep the TAP button pressed

down and select an amp model using the AMPS control.

s MIDI Thru: The MIDI OUT jack can be set to act as

MIDI THRU (see A).

Fig. 2.3: V-AMP PRO display

Tab. 2.1: Output formats and display LED assignments

The DISPLAY shows you what preset bank you have

selected and gives you information on parameter changes

when you are editing. In TUNER mode the DISPLAY shows

the pitch of the instrument connected to the unit. If one of

the amplifier simulations 17 - 32 has been selected, the

LED in the bottom left-hand corner of the DISPLAY lights

up. Additionally, the DISPLAY reads the digital format

output and the sample rate of your V-AMP PRO and

illustrates whenever the V-AMP PRO is synchronized by

an external word clock signal. Applied signals are indicated

by the SIGNAL LED, overload signals by the red CLIP LED.

DATA-MANFULL_V-AMP PRO_ENG_Rev_A.PMD 16.09.2002, 14:155

Скачать «BEHRINGER VIRTUAL AMPLIFICATION V-AMP PRO» — 1,97 МБ СкачатьСкачиваний: 0

Инструкция BEHRINGER VIRTUAL AMPLIFICATION V-AMP PRO — страница 5

Другие руководства из этой категории