Инструкция по эксплуатации ASKO T 175 Ceramic — страница 6

If the hotplate is supplied with an extensive area to switch the second area on bring the “Display of the cooking area” to position 9 and press the button + for 2 sec: until the decimal point is switched on to confirm.
To switch the hotplate off press the relative on/off button NOTE:( During operation it will be possible to block unblock the control zone by depressing the key button for 3 seconds).

· Timer Area (Fig.5)
The surface has the possibility to set the timer simultaneously on every cooking area The timer is a function that allows setting a time (from 1 to 99 minutes) to automatically switch off the selected cooking area.
Press the “Timer” button for 2 seconds: the display shows “00” in the centre and it will show which element is active on the right and left side.
By continuing to press the “Timer” button the hotplate is selected amongst those active.
Press + or to select the “Timer” value NOTE:
If the “Timer” function has been imposed for more than one cooking area the “Timer Display” will show every 3 seconds the remaining time for every programmed area.
To cancel the “Timer” function switch off the relative cooking area.

· “MEMORY” function This function allows the programming and execution of one cooking cycle on every warming element.

Note:
One cycle at a time can be carried out in registration or in execution.
The variations of power level for the times inferior to 15 sec are not registered.
One cooking cycle with a maximum duration of 10 hours and a maximum of 10 variations of the power level can be memorised.

· Memorisation of a cooking cycle Press the “Memory” button and then select the desired hotplate by means of the relative “ON/OFF” button.
Press the buttons + or until the desired power is selected.
To terminate the memorisation cycle press once again the button “ON/OFF”.

· Executing a cooking cycle To execute a cooking cycle already memorised it is sufficient to press the “ON/OFF” button of the interested cooking area followed by the “Memory” button.

· Display The cooking surface is supplied with a display that in normal function is a “WARCH” and can also carry out the “COUNTDOWN”
function when the surface is off.

· Regulation of the Watch In the installation phase set the clock in the following way:
Unblock the cooking surface by keeping the “key button” pressed down for 3 seconds until the “indicator light button” is switched off.
Press the buttons + or under the display until it begins flashing.
Press + or to set the desired time.
Press the “Timer” button to confirm the selection.

· Countdown Function Unblock the cooking surface by keeping the “key button” pressed down for 3 seconds until the “indicator light button” is switched off.
Press the “Timer” button until the writing “00” appears on the display.
Press + or to select the number of the minutes.
Press the “Timer” button to confirm the selection At the end of the set time an acoustic signal will be activated.

· Safety Systems 1 In the instance where an object is placed over the controls the cook top will switch off and the auto-protection system will activate automatically this occurs even in cases of liquid spills (water milk etc.) over the controls zone.
2 The commands keyboard has an internal temperature sensor that in the case that the internal temperature reaches 90° (abnormal use conditions of the surface without pots) the surface will automatically enter in an automatic system of temperature limitation: switching itself off automatically.

RESIDUAL HEAT

WARNING : when a cooking zone is switched off the surface of the cook top has a very high and dangerous temperature level The danger is highlighted by the fact that the “cooking zone display” will flicker until the temperature of the surface will not decrease to under 50°C.

· WARNINGS :
When the cook top is used with the power limitation (power level 2,4 3,4 4,4)) the following operation will guarantee the preset maximum power level absorbed :

A) After having switched on a number of cooking zones to their maximum power (position 9) the cook top may not accept the switching on of another “Cooking zone” and will emit an acoustic sound Or turn on the next cooking zone (heating element) at a diverse temperature than that desired B) When a number of cooking zones are switched on and there is a desire to increase the temperature value the cook top may not accept the increase and will emit an acoustic sound C) After having switched on a number of cooking zones at an intermediate temperature value then when another element is switched on then a few seconds delay may occur for the element to light up.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR
EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE
WARNINGS.