Инструкция по эксплуатации ASKO T 175 Ceramic — страница 5

ENGLISH

GENERAL

Carefully read the contents of this leaflet since it provides important instructions regarding safety of installation use and maintenance Keep the leaflet for possible future consultation All the operations relating to installation (electrical connections) must be carried out by specialised personnel in conformity with the regulations in force.

SAFETY WARNINGS

It is recommended to use flat-bottom pans with a diameter equal to or slightly larger than that of the heated area Do not use pans with a rough base to prevent scratching the heat surface of the cooktop (Fig.3).
This appliance is not suitable for use by children or persons requiring supervision Do not let children play with the appliance.

IMPORTANT

Avoid spilling liquid therefore to boil or heat liquids reduce the heat.

Do not leave the heating elements on with empty pots and pans or without receptacles.

When you have finished cooking switch off the relevant heating element with the control indicated below.

WARNING: If the surface is cracked switch off the appliance to prevent electric shock.

INSTALLATION INSTRUCTIONS

These instructions address specialised installers and serve as a guide for installation adjustment and maintenance in conformity with the laws and regulations in force.

If a built-in oven or any other appliance that generates heat must be fitted directly under the glass-ceramic cooktop THIS
APPLIANCE (oven) AND THE GLASS-CERAMIC COOKTOP
MUST BE SUITABLY INSULATED in such a way that the heat generated by the oven measured on the bottom right of the cooktop does not exceed 60°C Failure to respect this precaution may determine improper functioning of the TOUCHCONTROL system.

POSITIONING (Fig.1)
The domestic appliance is designed to be built into a worktop as illustrated in the specific figure Apply sealant around the entire perimeter (cut-out dimensions Fig.1B) Fix the domestic appliance on the worktop by means of the 4 brackets provided taking the thickness of the worktop into account (Fig.1A) If the lower part of the appliance after installation is accessible via the lower part of the cabinet then it is necessary to mount a separator panel respecting the distances indicated (Fig.1C) If the appliance is installed with an oven underneath then the separator is not necessary.

ELECTRICAL CONNECTIONS (Fig.2)
Before making the electrical connections check that:

the ground cable is 2 cm longer than the other cables;

the system ratings meet the ratings indicated on the identification plate fixed on the lower part of the worktop;

the system is fitted with efficient earthing compliant to the laws and regulations in force.

Earthing is obligatory by law If the domestic appliance is not fitted with a cable and/or relevant plug use material suited to the absorption value indicated on the identification plate and the operating temperature At no point must the cable reach a temperature 50°C higher than room temperature If wishing to make a direct connection to the mains an omnipolar switch must be interposed with a minimum opening of 3 mm between the contacts and suited to the load indicated on the plate and conform to the regulations in force (the yellow/green ground conductor must not be interrupted by the switch) When the appliance has been installed the omnipolar switch must be easily reachable Attention: The electronic card is protected against eventual connecting errors to the electric network by a fusible on board the card with the following characteristics: T40mA 250V

USE AND MAINTENANCE

MAINTENANCE
Remove any residues of food and drops of grease from the cooking surface using the special scraper supplied on request (Fig.4)
Clean the heated area as thoroughly as possible using SIDOL STAHLFIX or similar products and a cloth/paper then rinse with water and dry with a clean cloth Using the special scraper (optional) immediately remove any fragments of aluminium and plastic material that have unintentionally melted on the heated cooking area or residues of sugar or food with a high sugar content (Fig.4) In this way any damage to the cooktop surface is prevented Under no circumstances use abrasive sponges or irritating chemical detergents such as oven sprays or stain removers.

USE
If your appliance is predisposed then it will be possible to optimize energy consumption via the intelligent handling of the turning on and off of the cooking zones (hotplates) It is possible to set the maximum power absorption to 4 diverse levels: 2.4 KW 3.4 KW
4.4 KW Pmax The cook top is factory set with no power limitation (Pmax).

· Multi Level Power Control (MLP)
In the installation phase based on the available power in use it is possible to set the desired maximum power level absorbed in the following way:
Unblock the cooking surface by keeping pressed down the “key button” for 3 seconds until the “indicator light key” is switched off.
Press the button “E-plus” for 3 seconds: the watch’s display will show the power level formulated among those available: 2.4 KW/
3.4 KW/4.4 KW and FULL.
Press the buttons (+) or (-) to change level.
Confirm the choice by pressing the “E-plus” key within 10 seconds else it will return to the initial state.

· “E-PLUS” function During cooking it is possible to increase the maximum absorbed power level by passing from the formulated level to the immediately superior one by pressing the button “E-PLUS” until the relative indicator light is switched on When the surface is switched off it returns to the pre-formulated level Warning: normally the “E-PLUS” function is to be utilised when the maximum absorbed power from the surface is inferior to the available power in use.

· CONTROL AREA (Fig.5)
At the first ignition the cook top will be in the safety position that is the “key button warning light on/off” will be switched on.
To use the cook top it will be necessary to keep the “key button”
depressed for 3 seconds until the “key button warning light on/
off” switches off To turn on the desired heating element :
depress the corresponding on/off key The “led” of the “Cooking zone display” will be visualized flickering
depress the key within 10 seconds to go to position 4 or the +
key to go to position 9.
To regulate the temperature of the cooking zone use the + or
keys.