Инструкция по эксплуатации ViTESSE VS-657 — страница 3

Fill Water Tank

Make sure that the iron is unplugged from main socket before filling water into the water tank. 1 Set the adjustable steam knob to " 0 " position (Fig.2)
2 Take Anti-calc box out of the filling hole (Fig.3)
3 Using a cup slowly pour tap water or distilled water into the water tank as shown in Fig.4
Never to fill beyond the Max filling line.

4 Replace the Anti-calc box into the filling hole as shown in Fig.5
5 Hold the iron in horizontal direction and then move the iron front and back for about 30 seconds so that limescales in water can be purified by the ion exchange resin in the Anti-calc box.

fig.3

fig.4 fig.5

fig.2

Steam ironing

Note:
VS-657

VS-657-M:

Dry Ironing

Note:

1 Place the iron on a level horizontal ironing board 2 Set the adjustable steam knob to " 0 " position(Fig.2) and then fill the water tank with clean tap water refer to above filling instruction.

3 Connect the appliance to a suitable power socket set the temperature control button to "MAX" position The power indicator light will blink which indicate that the unit is being heated up When the power indicator light change to illuminate the required temperature has been reached In this stage it is normal that a "pong" sound produced it because that the steam switch automatically turn on.

4 For every first use press down the turbo steam button several times continuously and then press down the self-cleaning button for about 10 seconds to clean the steam chamber.

5 Set temperature control button to desired position according to different fabrics put the adjustable steam knob to " " position (Fig.6) and then steam will come out from steam vents of soleplate During steaming iron it is normal that the power indicator light cycle from blinking to illuminate steadily It is because the appliance automatically heat preservation.

6 After use turn adjustable steam knob to " 0 "position disconnect the appliance from power socket.

7 Before storing allow the unit completely cool down.

1 For every first use,the appliance should be pre-heated for about 2 minutes. 2 During steam ironing it is normal that steam is stopped for a while which may be caused by lower temperature of soleplate or steam rate is so high that the anti-drip system automatically reacted.

3 When setting the temperature control dial on ” ” position there are no steam go out of the soleplate since the temperature of soleplate is so low that it can not produce steam.

Allow the iron resting motionlessly on the soleplate or on its heel the unit will come into auto-shut off mode please refer to the auto-shut off function described below.

1 Place the iron on a level horizontal ironing board 2 Set the adjustable steam knob to “0”position(Fig.2). 3 Connect the appliance to suitable power socket and then set temperature control button to the desired position according to different fabrics The power indicator light will blink which indicate that the unit being heated up When the power indicator light change to steadily illuminate the required temperature has been reached It is ready for dry ironing.

4 If water spray is necessary press down the spray button two or three times in quick succession water can be sprayed evenly in the fabric.

5 After use disconnect the appliance from main socket. 6 Before storing allow the unit completely cool down.

When changing your temperature control button from high setting to lower it is proposed that not to start ironing immediately since there may be any burns caused on your fabrics by high temperature Please wait for the indicator light illuminate steadily and then start ironing.

FABRIC SETTING CHART

1 (Low)

2 (Medium)

3 (High)

(Max)

Shut off

Rayon Cotton Linen

Rayon Cotton Linen

Steam ironing

Iron while fabric is still damp using steam and spray

Use a press cloth and steam or dry ironing on the opposite side of the fabric

Wool Silk Polyester

Temperature Setting

Fabric

Iron Instructions

Dry Ironing on the opposite side of the fabric

Synthetics Nylon Acetate

Note:

When using distilled water you can mix it with tap water in a proportion of 50%.

fig.6