Инструкция по эксплуатации Vitek VT-3462 — страница 5

влажности тепла прямого солнечного света

• Держите магнитолу вдали от источников магнитных полей (телевизор акустические системы намагниченные объекты).

• Периодически протирайте корпус мягкой тканью с применением мыльного раствора После этого вытрите корпус сухой тканью.

• Не используйте химикаты и химически обработанные очищающие ткани.

- Не беритесь за шнур влажными руками.

СПЕЦИФИКАЦИЯ Питание

AC 230 В ~ 50 Гц;
DC12 В (D) x 8;

Частотные диапазоны

FM1 64 87 МГц;
FM2 88 108 МГц;
АM 540 1600 КГц;

Выходная мощность

5 Вт х 2 (RMS)
1500 Вт (Р.М.Р.О.)

Сопротивление динамиков

4 Ом

Сопротивление наушников

32 Ом

СРОК СЛУЖБЫ МАГНИТОЛЫ НЕ МЕНЕЕ 3 Х ЛЕТ

STOP/EJECT button (8)
Press the STOP/EJECT button (8) to cancel a selection i.e press this button during cassette play to stop the tape In stop mode press the button to eject the cassette PAUSE button (7)
The PAUSE button (7) can be used to interrupt a Recording or Playback temporarily and is useful for edit ing the content of the recorded tracks Press the button once to pause the recording press the button again to continue the recording Note: In Pause mode the Cassette motor is still energized therefore the feature should not be used for long periods of time

AUTOMATIC STOP The Cassette mechanism has a built in automatic stop During Playing/Recording the unit will automat ically stop when the end of the tape is detected.

TO PLAY A CASSETTE TAPE 1 Open the cassette door by pressing the cassette STOP/EJECT button (8). 2 Insert a cassette with the exposed tape facing upwards and the full reel on the right (unit plays from right to left) into the guides on the inside of the cassette door. 3 Close the cassette door. 4 Set the FUNCTION switch (6) to the TAPE position. 5 Press the cassette PLAY button (12) to start the tape playing. 6 Adjust the VOLUME CONTROL (5) to a comfortable listening level. 7 To stop the tape playing press the STOP/EJECT button (8) Press the button again to open the cas sette door and eject the tape Note: During play when the end of the tape is reached the PLAY button (12) will pop up and play will stop To play the other side of the tape remove the cassette turn the cassette over so that the full reel is on the right insert the cassette and press the PLAY button (12).

CARE OF CASSETTE TAPES TO HELP AVOID TANGLES Loose tape may jam or get tangled in the cassette recorder With a hexagonal pencil or a similar tool gen tly turn the pencil to tighten the tape as shown opposite If the spool feels tight when taking up slack tape as described above this may be due to ridges on the spool of tape Tight spools can lead to uneven play back speed or tape tangling In most cases the ridges can be removed by fast winding the cassette from one end to the other and back again Avoid the use of C120 tapes with this unit.

PROTECTING RECORDINGS FROM BEING ERASED. To prevent recordings from being erased accidentally break out the tab(s) with a screwdriver When the edge with the exposed tape is facing away from you the tab that protects the side that is uppermost is on your right as shown opposite To record on a protected cassette seal the open slots with adhesive tape.

MAINTENANCE If the sound becomes muffled or in any case after every 15 hours of operation clean the pinch roller cap stan erase head and record play head Open the cassette door and use a cotton bud moistened with special tape head cleaning fluid.

CAUTION Never touch any of the parts described above with a metal object Do not insert a cassette until the cleaned parts are completely dry.

AUTOMATIC LEVEL CONTROL (ALC)
This set has the latest Automatic Level control circuitry therefore it is not necessary to adjust the Volume Control when recording This circuit automatically records at the correct level and prevents over loading Note: While recording you may adjust the VOLUME control (5) as you desire without affecting the record ing operation.

ENGLISH

РУССКИЙ

VT-3462.qxd 29.01.03 16:01 Page 10