Инструкция по эксплуатации Vitek VT-1224 — страница 6

ФорматФормат: Руководство СтраницСтраниц: 8 КатегорияКатегория: Утюги ДобавилДобавил: OLD

Инструкция для Инструкция по эксплуатации Vitek VT-1224 на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

Назад
/ 8
Вперёд
Страница 6
НАПОЛНЕНИЕ УТЮГА ВОДОЙ:

- Убедитесь что утюг отключен от сети Установите выключатель подачи пара (7) в положение "O" (рис 2)

• Откройте заливочное отверстие для этого сдвиньте крышку (4) вниз.

• Налейте воду в заливочное отверстие (рис.3)

ТЕМПЕРАТУРА ГЛАЖЕНИЯ

Выбор температуры

• Ensure that there is enough water in the water tank.

• Stand the iron on its rear side.

• Insert the plug into the wall socket.

• Set the Temp Control Knob (12) at the required position within the higher ironing temperature range (•• or ••• or MAX) (Fig5)

• Wait a little while for the indication light (12) to go out and to come on again Set the Continuous

Steam Rotary Knob (7) to the position "

"(Fig.6)

NOTICE:
Water may leak from the soleplate if the temperature selected is too low This will then cause stains If it happens set the Temperature Control Knob (12) to the advised position Steaming will re-commence as soon as the appropriate temperature has been reached.

SHOT OF STEAM

• Set the Temp Control Knob (12) to the ••• or "MAX" position.

• By pressing Shot Of Steam Button (6) an intense "Shot of steam"

is emitted from the soleplate (Fig 7)

This function can be very useful e.g when removing stubborn creases The "Shot of steam" facility can be used only while ironing with high ironing temperature (positions at •• ••• or MAX)

DRY IRONING

• Insert the mains plug into the wall socket.

• Ensure that the Continuous Steam Rotary Knob (7) is in position"O".

• Select the setting on the Temp Control Knob (12) best suited for the fabric to be ironed.

• When the indication light is gone ironing may commence.

SELF CLEAN (Auto Clean System)

• To prolong the life of your iron we recommend that this should be carried out at regular intervals (once or twice a month)

• Fill the water tank to the symbol "MAX"

• Stand the iron on its rear side.

• Insert the mains plug into the wall socket.

ENGLISH

РУССКИЙ

Fig.5

Fig.6

Fig.7

синтетика синтетика синтетика шелк шерсть хлопок лен акрил полипропилен полиэтан ацетатволокно триацетат с люрексом полиамид (нейлон)

полиэстер вискоза шелк шерсть хлопок лен

Vt-1224new.qxd 16.08.2004 14:23 Page 10
Нашли ошибку?