Инструкция SKIL 9390 LA — страница 8

Инструкция

PDF

3,93 МБ

176

Инструменты / Контрольно-измерительные приборы

LeoMaster9

Инструкция для SKIL 9390 LA на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of

this tool, it must be disposed of safely and not left

unattended

USE

• Mounting of accessories

! disconnect the plug

- clean spindle A and all parts to be mounted

- tighten clamping ange B with spanner C while

pushing spindle-lock button D

! push spindle-lock button D only when spindle A

is at a standstill

- for removing accessories handle vice-versa

! grinding/cutting discs become very hot during

use; do not touch them until they have cooled

down

! always mount backing pad when using sanding

accessories

! never use a grinding/cutting disc without

the label (“blotter”) which is glued onto it (if

provided)

• Mounting of auxiliary handle E

! disconnect the plug

- screw auxiliary handle E on the right or the left of the

tool (depending on the work to be carried out)

• Adjusting of protective guard F

! disconnect the plug

! ensure that the closed side of the protective

guard always points to the operator

• Removing of protective guard F

! disconnect the plug

- for mounting protective guard, handle in reverse order

• Before using the tool

- ensure that accessory is correctly mounted and rmly

tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 30 seconds at highest no-load

speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

• On/o locking switch H

- switch on tool

! be aware of the sudden impact when the tool is

switched on

! before the accessory reaches the workpiece, the

tool should run at full speed

- lock switch

- unlock switch/switch o tool

! before switching o the tool, you should lift it

from the workpiece

! the accessory continues to rotate for a short time

after the tool has been switched o

• Grinding

- move the tool back and forth with moderate pressure

! never use a cutting disc for side grinding

• Cutting

- do not tilt the tool while cutting

- always move the tool in same direction as arrow on

tool head, in order to prevent the tool from being

pushed out of the cut in an uncontrolled manner

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when original accessories are used

• Use only grinding/cutting discs with a maximum

thickness of 8 mm and a spindle hole diameter of

22 mm

• For mounting/using non-SKIL accessories observe the

instructions of the manufacturer concerned

• Never use reducors or adaptors to t large-hole

grinding/cutting discs

• Never use accessories with a "blind" threaded hole

smaller than M14 x 21 mm

OUTDOOR USE

• Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

BEFORE USE

• Before using the tool for the rst time, it is recommended

to receive practical information

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Always mount auxiliary handle E

and protective

guard F

; never use the tool without them

• Use suitable detectors to nd hidden utility lines

or call the local utility company for assistance

(contact with electric lines can lead to re or electrical

shock; damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Do not work materials containing asbestos

(asbestos is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Be careful when cutting grooves, especially in

supporting walls (slots in supporting walls are subject to

country-specic regulations; these regulations are to be

observed under all circumstances)

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Do not clamp the tool in a vice

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

DURING USE

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• In case of current interruption or when the plug is

accidentally pulled out, immediately switch o the tool in

order to prevent uncontrolled restarting

AFTER USE

• After switching o the tool, never stop the rotation of the

accessory by a lateral force applied against it

Скачать «SKIL 9390 LA» — 3,93 МБ СкачатьСкачиваний: 0

Инструкция SKIL 9390 LA — страница 8

Другие руководства из этой категории