Инструкция по эксплуатации Saturn ST-CH7401 — страница 3

INSTRUCTIONS FOR USE Low speed:

for simmering and dishes which do not produce much steam to ventilate the kitchen

Medium speed:
for standard cooking operations

High speed:

when large amounts of smoke or steam are being produced (deep frying pressure cooking )
always return to medium speed as soon as possible

For maximum efficiency from your hood:
Use the rear cooking areas on your stove in prefence

we advise you to turn the extractor hood on as soon as you start cooking and if necessary keep it running for a few minutes after you have finished cooking NB:

Change the air in the room of ten by ventilating it as much as possible Note that at high speed the volume of air in a kitchen is changed within a few minutes

IMPORTANT Do not use the hood without the Alu filters

B WHEN TO CLEAN YOUR HOOD 1) REGULAR CLEANING Never use metal scouring pads abrasive cleaning products or very stiff brushes For cleaning the bodywork and the light cover use a commercial household cleaning product exclusively diluted with water then rinse with clean water and dry with a soft cloth. 2) MONTHLY CLEANING: cartridge filter ESSENTIAL: clean these filters every month to prevent any risk of fire

The filter collects greasy smoke and dust and is an element which plays an important role in the efficiency of your range hood

It can become in flammable when it is saturated with greasy residues Clean it with a commercial household cleaning product then rinse well and dry This cleaning can be done in your dishwasher with the filter in an upright position (do not allow it to come into contact with dirty dishes and pans)

Before using the cartridge filter for the first time remove the protective film

To take off the cartridge filter 1 Push it back supporting it with one hand 2 Then pivot the filter downwards

After cleaning replace the filter carrying out the same operations in reverse order 3) ANNUAL CLEANING: activated carbon filter

Applies

SOLELY to range hoods installed as a recirculation unit (not vented to the outside) This filter traps odors and must be changed at least once a year depending on how much it is used Order these filters from your dealer (using the reference number shown on the identification plate inside the hood) and keep a note of the date it was changed

WARNING:

Disconnect the hood before doing any servicing 1 Remove the filters. 2 Place the new carbon filter in the hook of blower inside surface then turn in direct way. 3 Repeat the same operation for all the cassette filters. 4 Fix the filters again

C CHANGING THE BULBS:
Disconnect the hood either by unplugging it or switching it off before doing any servicing 5

MODEL USING LIGHT BULB OR NEON TUBE 1 Unscrew the screw securing the light cover 2 Tip it back. 3 Model using type E14 40W light bulb change the bulb by unscrewing it and screwing in the new one (see diagram opposite) 4 Replace the light cover. 5 Screw back the light cover

MODEL WITH HALOGEN LIGHTING 1 Remove the chrome rims "A" by turning them anti-clockwise. 2 Change the type GU10-20W-12V by unscrewing them. 3 Replace the assembly by carrying out the operations in reverse order

INSTALLATION

A General points If you have an outlet to the outside:

Your range hood can be connected to this by means of an extraction duct (enamel aluminum flexible pipe or non-flammable material with an interior diameter of 150mm) (supplied with your hood)

If you do not have an outlet to the outside:

All our appliances have the option of operating in recirculation (with no outlet to the outside)

Under these circumstances add an activated carbon filter which will trap odors (see illustration p.5)

These filters are available from your dealer under the reference indicated on the identification plate (see inside hood)

B Fitting 1) Pre-fitting recommendations:

Your hood must be 70cm above your hob To fit it correctly:

Draw a vertical line on the wall to centre your hood (and its chimney)
correctly over your cooker

Make a mark on the vertical line 70 cm above your hob surface This vertical line and the mark at 70 cm will help you to position correctly the fitting template supplied 2) Fitting the hood:

A If the model with Glass:
To install onto the wall every 100mm drill 3 holes which diameter is 8mm on a suitable place in line with the hook of the hood

Insert expended screws into the holes

Fix the hook on the wall put drilling template on the hook See pic 1. Add the soot tube to the one way valve and put it outdoor See pic 2. Place two chimney on the hood See pic 3A

Place the glass according with the direct of the lead Use for screws to fix the glass when install the screws of the glass please do not tight strongly to avoid the glass cracking See pic 3B. Drill 2 holes of 8mm on a suitable place in line with the 2nd plate and fix (see pic 4A) then place two screws