Инструкция REMS 845001 — страница 6

Инструкция

PDF

1,99 МБ

Инструменты / Контрольно-измерительные приборы

OlegReader

Инструкция для REMS 845001 на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

eng eng

g) Use the power tool, accessories and tool bits etc. in accordance with these

instructions, taking into account the working conditions and the work to

be performed. Use of the power tool for operations different from those intended

could result in a hazardous situation.

h) Keep handles dry, clean and free from oil and grease. Slippery handles do

not allow for safe handling and control of the tool in unexpected situations.

5) Service

a) Have your power tool serviced by a qualied repair person using only

identical replacement parts. This will ensure that the safety of the power tool

is maintained.

Safety Instructions for pipe cutting machines

WARNING

●

Do not overload the pipe cutting machine. Do not use damaged cutting wheels.

Use moderate feeding pressure.

●

 Caution!Keephair,clothingandglovesawayfromthepiperestwhenapipeis

rotatingintherollers.Looseclothing,jewelleryorlonghaircouldgetcaught

between the rotating pipe and the rollers.

●

Do not reach into the rotating cutting wheel.

●

 WherenecessaryuseamaterialsupportREMSHerkules(Art.No.120100)on

each side to support long pipes and position the pipe and material support(s)

exactlywiththepipesupport(3)ofthepipecuttingmachine.

●

 Iftheconnectingcableneedstobereplaced,thismustbedonebythemanu-

facturerorhisrepresentativetoavoidsafetyrisks.

●

Remove blockages of dust, chips and fragments of the workpiece.

Explanation of symbols

Read the operating manual before starting

Environmentalfriendlydisposal

Power tool corresponds to protection class I

Power tool corresponds to protection class II

1. Technical Data

Use for the intended purpose

Use the REMS Cento for cutting and removing burr from inside and outside of pipes.

WARNING

All other uses than those mentioned above are not for the intended purpose and

are not permitted.

1.1. Article numbers

REMS Cento 845001

REMS cutter wheel Cu-INOX 845050

REMS cutter wheel V 845051

REMS cutter wheel St 845052

REMS cutter wheel Cu 845053

REMS cutter wheel Cu-SF

(for carbon steel pipe with welded chamfer) 845055

Stand 849315

Rollers INOX (set) for stainless steel pipes 845110

Ring spanner SW 27/17 849112

REMS Herkules material rest with 3 legs 120100

REMS Herkules Y material rest with clamp 120130

REMS Jumbo collapsible workbench 120200

REMS REG 10 – 54 E 113835

REMS REG 28 – 108 113840

1.2. Application Area

Stainless steel pipes, copper pipes, composite tubes,

 carbonsteelpipesofthepressttingsystems Ø22–108mm

 Plastic/compositetubes Ø25–110mm

 SteelpipesDINEN10255(DIN2440) DN20–100mm,Ø¾–4”

Cast pipes (SML) DN 50 – 100 mm

Max. wall thickness steel pipes, copper pipes

Cast pipes (SML) depending on cutting wheel 4.5 mm

Max. wall thickness composite tubes 10 mm

1.3. Speed

Idle speed of cutting wheel 115 rpm

1.4. Electrical Data

230 V 1~; 50 – 60 Hz; 1200 W; 5.7 A or

110 V 1~; 50 – 60 Hz; 1200 W; 11.4 A

Fuse (mains) 10 A (B), cut-out S3 20% (AB 2/10 min), insulated, radio

interference suppressed.

1.5. Dimensions

 L×W×H: 250×300×250mm(10”×12”×14”)

1.6. Weights

REMS Cento without foot switch 17.8 kg (39 lbs)

1.7. Noise Data

Sound pressure level L

pA = 87 dB

Operating sound level Lwa = 98 dB

Sound pressure level Lpc peak = 100 dB

K = 3 dB

1.8. Vibrations

Weighted effective value of the acceleration < 2,5 m/s²

K = 1,5 dB

The indicated weighted effective value of acceleration has been measured

againststandardtestproceduresandcanbeusedbywayofcomparisonwith

another device. The indicated weighted effective value of acceleration can also

beusedasapreliminaryevaluationoftheexposure.

ATTENTION

The indicated weighted effective value of acceleration can differ during operation

from the indicated value, dependent on the manner in which the device is used.

Dependentupontheactualconditionsofuse(periodicduty)itmaybenecessary

toestablishsafetyprecautionsfortheprotectionoftheoperator.

2. Commissioning

2.1. Electrical Connection

WARNING

Pay attention to mains voltage! Before connecting the device, make sure

thatthevoltagespeciedontheratingplatematchesthemainssupply.

2.2. Installation of the Machine

Bolt the pipe cutting machine to a workbench or similar or to the stand (Fig. 2)

(Art.No. 849315) using 4 x M8 screws. Where applicable, longer pipes should

be supported on both sides using REMS Herkules (Fig. 2) (Art.No. 120100).

2.3. Installing (changing) the cutter wheel (2)

Pull out the mains plug! Select a suitable cutter wheel:

●

REMS cutter wheel Cu-INOXforpipesofthepressttingsystemsofstain-

less steel, copper, carbon steel,

●

REMS cutter wheel V for plastic and composite tubes, wall thickness

s≤7mm,

●

REMS cutter wheel St for steel pipes, cast iron pipes (SML), usable from

machine no. 630000 and onwards,

●

REMS cutter wheel Cuespeciallyforcopperpipesofthepresstting

systems,

●

REMS cutter wheel Cu-SF for cutting carbon steel pipes whilst simultane-

ouslyproducingaweldingchamfer.

Loosen the hexagonal nuts which fasten the cutting wheel (right-hand thread)

with the size 27 ring spanner provided. Insert (change) the cutting wheel (2).

Make sure that the carrier pins of the drive shaft grip into the holes of the cutting

wheel.Tightenthehexagonalnutsrmly.

NOTICE

If an unsuitable cutting wheel is used, the wheel will be damaged or the pipe

will not be cut. Only use original REMS cutting wheels!

3. Operation

CAUTION

Danger of injury!

 Keephair,clothingandglovesawayfromthepiperestwhenapipeisrotating

intherollers.Looseclothing,jewelleryorlonghaircouldgetcaughtbetween

the rotating pipe and the rollers. For long pipes, make sure that no persons are

endangeredbytherotatingpipe.

3.1. Work Procedure

Mark the cut on the pipe. Move the cutting wheel drive (1) far enough up or

downbyturningthefeedlever(6)toallowthepipetobecut(5)tobeinserted

in the pipe rest. Remove external burr (sawing burr) to avoid damaging the

rollers.

CAUTION

Support longer pipes (see 3.2.) (Fig. 2)!

 Pressthefootswitch(8)andcutthepipewithmoderatefeedbyturningthe

feed lever (6).

CAUTION

The cut pipe sections can fall to the oor immediately after being cut!

3.2. Supporting the Material

 LongerpipesmustbesupportedbytheREMSHerkules(Art.No.120100)on

bothsidesofthemachineifnecessary(Fig.2).

3.3. Deburring

Deburring of inside of pipe

 WiththeREMSREG28–108pipesofØ28–108mm,Ø¾–4”canbedeburred

ontheinside.TheREMSREG28–108isdrivenbythecutterwheel(Fig.3).

NOTICE

Make sure that the blade of the cutting wheel protrudes into the groove of the

REMS REG 28 – 108.

Скачать «REMS 845001» — 1,99 МБ СкачатьСкачиваний: 0

Инструкция REMS 845001 — страница 6

Другие руководства из этой категории