Инструкция KORTING КНС 9959 X — страница 10

Инструкция

PDF

1,65 МБ

Климатическая техника

OlegLab494

Инструкция для KORTING КНС 9959 X на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

outside the lower part. Do not connect the cooker hood ex-

haust to the same conductor used to circulate hot air or for

evacuating fumes from other appliances generated by other

than an electrical source. Before proceeding with the assembly

operations, remove the anti-grease lter(s) (Fig.2.2 - Fig.3.2)

so that the unit is easier to handle.

- In the case of assembly of the appliance in the suction version

prepare the hole for evacuation of the air.

•We recommend the use of an air exhaust tube which has the

same diameter as the air exhaust outlet hole. If a pipe with

a smaller diameter is used, the eciency of the product may

be reduced and its operation may become noisier.

•If the appliance is supplied with the small cupola M remove

it by releasing it as indicated in Fig.2.3 - Fig.3.3.

Before proceeding with the assembly operations, for easier

manoeuvrability of the appliance disengage the anti-grease

lter by pulling handle B as indicated in Fig.2.2 - Fig.3.2.

If one owns a model with perimeter suction panel, before

carrying out this operation, perform the following phases:

- Open panel C as indicated in Fig.2.1 - Fig.3.1.

- If one owns the version with three A panels release them

from the xing pins by pulling outwards (Fig.3.4) and then

remove them from safety pins N (Fig.3.4) placed inside the

hood. To put them back perform the operation in reverse

order. ATTENTION! During this disassembly and assembly

operation ensure to hold the panel securely to prevent

accidental falls.

•Wallmounting:

Trace the bottom side of the hood on the wall. Consider the

measurements shown in Fig.4A and minimum distance from

the cooking surface (Fig.4B).

- Position the xing template on the wall, making sure that

the line coincides with the line previously made on the wall.

- Mark the xing holes and cut them into the material (Fig.5).

- Fix the 2 top screws K and screw anchors (Fig.5), without

tightening them completely.

- Position the appliance at the wall (Fig.6A).

- Make sure the 2 levelling screws J are tightened (Fig.6B.1).

- Align the appliance horizontally using the two levelling

screws J (Fig.6B.1).

- Once the adjustment has been made, fasten the hood per-

manently using the screws K (Fig.6C - Fig.6D).

- For easy accessibility to the motor unit in the case of assistan-

ce, after having levelled and xed the appliance denitively,

we recommend that the brackets are removed (Fig.6B.1).

- When carrying out the xing operations, use only screws

and screw anchors suited to the type of wall (e.g. reinforced

concrete, plasterboard etc.).

- If the screws and screw anchors are supplied with the ap-

pliance, make sure that they are suited to the type of wall to

which the hood must be xed.

•Installationofmodelswithoutdecorativeducts:

Extractor hood

- Unclip the canopy M and remove the grille E (Fig.7).

- Pass the power supply cable through the slot in the canopy

M, as indicated in Fig.9A.1.

- Taking the grommet H, position it between the power cable

and the slot (Fig.9A.2).

- Connect the flexible hose L (not supplied) to the hood

(Fig.9B).

- Re-position the small cupola M paying attention that it is

hitched perfectly to the xing pins G (Fig.9B).

•Filteringversion:

- Unclip the canopy M and remove the grille E (Fig.7).

- Pass the power supply cable through the slot in the canopy

M, as indicated in Fig.8.1.

- Taking the grommet H, position it between the power cable

and the slot (Fig.8.2).

- Fix the small cupola M and the grille E making sure that is it

perfectly hooked on to the fastening pins G (Fig.8).

•Optionalaccessories:

This model may have decorative ducts as optional accessories

- ask your retailer for information.

Before installing decorative ues it is necessary to remove

the small cupola M and loosen the 4 screws Q that lock the

fastening pins G as shown in Fig.11.

•Installationofmodelswithdecorativeducts:

Extractor hood

Make sure the electrical power supply is within the measure-

ments of the decorative connector. Adjust the width of the

support bracket of the top connector (Fig.10.2). Then x it

to the ceiling so that it is on the same axis as the hood using

screws A and observing the distance from the ceiling shown

in Fig.10.1. Connect ange F to the air exhaust hole using

exible hose L (Fig.12A). Slide the top connector inside the

lower duct and place this on the body (Fig.12B). Pull out the

top duct as far as the bracket and secure it using screws B

(Fig.10.2). To transform the hood from a ducting version into

a ltering version, ask your dealer for the charcoal lters and

follow the installation instructions.

•Filterhood:

Please note:

The lters must be ordered from your dealer as an acces-

sory.

- To transform the hood from the SUCTION version to the

FILTERING version, charcoal lters must be ordered from

your dealer as an accessory. Two types of kit are available,

one with non-renewable lters (Fig.13) and the other with

renewable lters (washable) (Fig.14). Unlike traditional carbon

lters, this carbon lter can be washed and reactivated for

approximately 12-15 times. With normal hood use, this lter

should be cleaned once every 2-3 months. The lter can be

washed into a dishwasher at the highest temperature using a

standard dishwasher detergent. After washing, dry the lter in

the oven at 100°C for 10-15 minutes to reactivate it. The lter

will retain its odour-absorbing capacity for three years, after

which it will have to be replaced.

- If a bracket is found in the packaging like that indicated in

Fig.14 loosen the screws already installed inside the hood and

install the bracket using the previously-removed screws.

- To replace re-usable carbon filters Y, remove the brackets

from their seat, pulling them outwards (Fig.14).

- If your product is not supplied with the bracket, it means

that the active charcoal lter cannot be renewed (Fig.13).

These must be applied to the suction unit inside the hood,

centring them in it and turning them 90° until they snap into

place (Fig.13).

USE AND MAINTENANCE

•We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

- 10 -

Скачать «KORTING КНС 9959 X» — 1,65 МБ СкачатьСкачиваний: 0

Инструкция KORTING КНС 9959 X — страница 10

Другие руководства из этой категории