Инструкция KORTING KHА 9770 X — страница 10

Инструкция

PDF

4,08 МБ

Климатическая техника

ИванUser61

Инструкция для KORTING KHА 9770 X на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

If a connection tube composed of two parts is used, the upper

part must be placed outside the lower part. Do not connect the

cooker hood exhaust to the same conductor used to circulate

hot air or for evacuating fumes from other appliances gener-

ated by other than an electrical source. Before proceeding

with the assembly operations, remove the anti-grease lter(s)

(Fig.15) so that the unit is easier to handle.

- In the case of assembly of the appliance in the suction version

prepare the hole for evacuation of the air.

•We recommend the use of an air exhaust tube which has the

same diameter as the air exhaust outlet hole. If a pipe with

a smaller diameter is used, the eciency of the product may

be reduced and its operation may become noisier.

N.B.!

- Two people are needed to install this product.

Attention!

- Before installing the appliance, x the electrical box D.

- Lift the electrical box and follow phases 1-2-3 indicated in

gure 2.

- Position the bracket in correspondence with the 3 screws G

already set up on the container and screw them is indicated

in phase 4 - gure 2.

- Fix the air exhaust pipe H (not included) on the air outlet

ange F as indicated in gure 2.

•Mountinghood:

- Remove the structure D from the packaging and x it to the

motor container with the 4 screws E g.3.

- Remove the 2 screws A fastening the upper structure B to

the lower structure C as indicated in g.4.

- Adjust the desired height paying attention to the quota in-

dicated in gure 5 and block it with the 8 screws G provided.

- Couple the lower chimney A to the upper one B and insert

it on the structure as indicated in gure 6.

- Position the perforation template on the ceiling making

sure the arrow is positioned on the same side as the appli-

ance control (Fig.7).

- Drill 4 Ø8 holes in the ceiling and tighten the 3 screws with-

out pulling them completely making sure not to insert the

screw in the hole marked with an X on the perforation tem-

plate g.8 (the screws and expansion plugs must be suited

for the type of wall).

- Take the hood and insert the upper telescopic structure on

the 3 screws E not tightened completely corresponding to

the 3 slots and turn them slightly to t them as indicated in

gure 9 - phase 1-2.

Tighten the fourth screw X and pull the other 3 to perma-

nently block the upper part of the structure B as indicated in

gure 9 - phase 3-4.

- Suction version: Fix the exible tube to the pre-arranged

air exhaust hole (Fig.10).

- Filtering version:

-Connect the exible tube H to the deector M and secure

the screw I as indicated in (Fig.11).

The lters must be applied to the suction unit inside the

hood, centring them and turning them 90 degrees until they

click stop (Fig.16).

- Perform the electrical connection (g.12).

- Fix the upper chimney B to the structure with the 4 screws

F (g.13).

- If the cooker hood is supplied with a lower chimney piece

that must be xed to the hood body with screws, remove the

anti-grease lters from the hood by acting on the relevant

handles (Fig.15).

- If necessary, x the lower duct to the hood from the inside,

using the screws P (Fig.13). Re-locate the lters in their seat.

USE AND MAINTENANCE

•We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air.

The eective performance of the cooker hood depends on

constant maintenance; the anti-grease lter and the active

carbon lter both require special attention.

•Theanti-greaselter is responsible retaining the grease

particles suspended in the air, therefore it is subject to clog-

ging with variable frequency according to the use of the

appliance.

- To prevent the danger of possible res, at least every 2

months one must wash the anti-grease lters by hand using

non-abrasive neutral liquid detergents or in the dishwasher

at low temperatures and on short cycles.

- After a few washes, colour alterations may occur. This does

not give the right to claim their replacement.

•Theactivecarbonlters are used to purify the air that is

sent back into the room and its function s to mitigate the

unpleasant odours produced by cooking.

- The non-regenerable active carbon lters must be replaced

at least every 4 months. The saturation of the active charcoal

depends on the more or less prolonged use of the appliance,

on the type of kitchen and on the frequency with which anti-

grease lter is cleaned.

- Regenerable active charcoal lters must be washed by hand,

with non abrasive neutral detergents, or in the dishwasher at

a maximum temperature of 65°C (the washing cycle must be

complete without dishware). Remove excess water without

damaging the lter, remove the plastic parts, and let the mat

dry in the oven for at least 15 minutes approximately at a

maximum temperature of 100°C. To keep the regenerable

charcoal lter functioning ecient this operation must be

repeated every 2 months. These must be replaced at least

every 3 years or when the mat is damaged.

•Beforeremountingtheanti-greaseltersandtheregen-

erable active charcoal lters it is important that they are

completely dry.

•Cleanthehoodfrequently,bothinternallyandexter-

nally, using a cloth dampened with denatured alcohol or

neutral liquid detergents that are non abrasive.

•The lighting .system is designed for use during cooking

and not for the prolonged general lighting of the room. The

prolonged use of the lighting system signicantly decreases

the average duration of the bulbs.

•If the appliance is equipped with courtesy lights it is possible

to use them for general room lighting for a prolonged amount

of time.

•Attention: The non compliance with the hood cleaning

warnings and with the replacement and cleaning of the lters

entails risk of res. One therefore recommends keeping to the

suggested instructions.

•Replacinghalogenlightbulbs(Fig.17):

To replace the halogen light bulbs B, remove the glass pane

C using a lever action on the relevant cracks.

Replace the bulbs with new ones of the same type.

Caution: Do not touch the light bulb with bare hands.

•ReplacingLEDlamps(Fig.18):

If the appliance version is with LED lamps, the intervention of

a specialised technician is necessary to replace them.

- 10 -

Скачать «KORTING KHА 9770 X» — 4,08 МБ СкачатьСкачиваний: 0

Инструкция KORTING KHА 9770 X — страница 10

Другие руководства из этой категории