Инструкция GRILLO MD 13 — страница 10

Инструкция

PDF

17,71 МБ

Садовая техника

MiraТех342

Инструкция для GRILLO MD 13 на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

MD13-MD16/ Translation of the original instructions

PUTTING THE MACHINE INTO SERVICE

1) Check that the machine has not been damaged during transport.

2) Check the oil levels of the engine, hydrostatic transmission and final drive.

3) Check the tyre pressure:

1 bar front wheels 13 x 5.00-6

1.2 bar rear wheels 16 x 7.50-8.

4) Check the battery voltage; it must be at least 12 Volts. Charge if necessary.

5) IMPORTANT!!! During assembly take care not to reverse the polarity of the battery.

Fix the steering wheel taking care the key is properly inserted and the screw is tight enough (tightening

torque 2 KgF.m [20 N.m]).

6) Fit the muffler, the rear bumper and the roll bar (on MD16 only).

RUNNING IN - CAUTION!!

Change the engine oil and filter after the first 20 working hours.

Check that there are no oil leaks or slack screws, especially those which fix the blade and the steering.

INSTRUCTIONS FOR USE

BEFORE STARTING UP THE ENGINE

Before starting up the engine, always check that:

– the travel lever is in the idle position (fig. 3);

– the engine oil level is correct (fig. 4);

– the engine cooling intake grilles are clean (fig. 4);

– air filter is clean (fig. 8).

– the mowing deck is clean;

– the hydraulic motor fins are clean (fig. 5);

– the blades are sharp and firmly fastened in place;

– the screw in the centre of the blade hub is safety tightened ( fig. 9, ref.3)

Fill the fuel tank using a funnel with very fine filter ( fig.10).

Adjust the seat by using the lever (fig. 11 – MD16).

STARTING UP THE ENGINE

– Push the throttle half way in fig. 3, ref. 5)

– If the engine is cold, use the choke (fig. 3, ref. 6 – MD16; fig. 3, ref. 5 – MD13). Turn the ignition key

(fig. 1, ref. 1).

– Once the engine has started, turn off the choke and wait for a few minutes to allow the engine to warm

up.

– To switch off the engine put the ignition key into the STOP position (fig. 1, ref. 1).

N.B. When travelling with the mower from one place to another, you are advised to keep the cutting deck

at the maximum height setting.

SWITCHING ON THE HEADLAMP

To switch on the headlamp, put the ignition key in the second position (fig. 18, position A).

IMPORTANT

It is necessary to switch on the headlamp once the engine has started up to avoid battery discharge.

STARTING WORK

– Choose the desired cutting height by means of the lever ( fig. 2, ref. 8). Suitably accelerate the engine

and engage the PTO lever using the switch on the dashboard (Fig.1, ref.6). Gently operate the forward

travel lever (fig. 3, ref. 2) and start work. To stop, return the forward travel lever to the stop position.

Скачать «GRILLO MD 13» — 17,71 МБ СкачатьСкачиваний: 0

Инструкция GRILLO MD 13 — страница 10

Другие руководства из этой категории