Инструкция GRILLO GF 3DF — страница 9

Инструкция

PDF

5,19 МБ

Садовая техника

ИванTech32

Инструкция для GRILLO GF 3DF на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

GF3 – Translation of the Original Instructions

8) Verify the tyre pressure according to the table provided below:

TYRE PRESSURE

20×10.00-8 2 PLY RATING 0,8 BAR

4.00-8 2 PLY RATING 1,1 BAR

4.00-10 2 PLY RATING 1,1 BAR

5.00-10 2 PLY RATING 1,5 BAR

9) Check that the clutch cable has free-play (10 mm) between the adjustment screw and the clutch

lever (fig. 6).

10) Fill the tank with fuel using a funnel provided with a fine filter.

11) Check liquid levels when the machine is horizontal.

Before starting the engine always check:

− the oil levels inside the engine (Fig. 3) and in the gearbox; the level check cap is on the

upper cover (Fig. 4); the oil level must be between the two notches.

− that all screws and nuts are well tightened.

− that all levers are in neutral position.

− that the air filter is clean (Fig. 5).

− that the clutch lever has free-play (Fig. 6).

− fill the tank with fuel, using a funnel with very fine filter.

Once the engine is running, deactivate the choke and speed up gradually. Let the engine warm up

a bit before starting to work.

INSTRUCTIONS FOR USE

STARTING THE PETROL ENGINE

Turn on the petrol cock, push the throttle lever to the midway position and, if the engine is cold,

engage the choke on the carburettor. Start the engine by pulling hard on the pull starter handle

(Fig. 1C, no. 3). Always refer to the instructions in the engine manual.

STARTING THE DIESEL ENGINE

Push the throttle lever to the midway position (see engine manual), press the decompresser lever

on the engine head until it remains in position and start the engine by pulling hard on the pull

starter handle.

STARTING THE MACHINE

Set the gearbox lever in the desired position. If the gear does not engage immediately, give a few

light touches on the clutch. Press the clutch lever slowly until the machine starts moving.

STARTING WORK

Engage the P.T.O. (Fig. 1A no. 9). Increase speed as appropriate and press the clutch lever to

start work.

The machine will start by depressing the lever 12 (Fig. 1A) and then subsequently on the red lever

2 (Fig. 1A) until it comes into position 2A. By releasing the red lever, the machine will stop but the

engine will keep running and the lever returns back to position 2.

NOTE: to avoid problems to the clutch during the functioning of the machine, please keep the red

lever firmly depressed. Attention! Do not use the machine whilst only partially depressing the red

lever or damage to the clutch may result.

END OF WORK

When work is ended, to turn the engine off, turn the switch positioned on the handle 13 (Fig. 1A),

position OFF for petrol engines. For Diesel engines, turn the handle 14 (Fig. 1A).

Скачать «GRILLO GF 3DF» — 5,19 МБ СкачатьСкачиваний: 0

Инструкция GRILLO GF 3DF — страница 9

Другие руководства из этой категории