Добавить

Инструкция GRILLO Climber 9.21 — страница 15

Инструкция ФорматPDF Размер6,22 МБ Страниц48 КатегорияСадовая техника ДобавилМилаДок929

Инструкция для GRILLO Climber 9.21 на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

← Назад
/ 48
Вперёд →

HYDRAULIC MOTOR
Check the level in the expansion tank when the motor is cold. It should come up to the level notch Fig.
3. If necessary, add AGIP SAE 15W50 or 20W50 oil. Change the oil every 200 working hours. To drain
WKHRLOXQVFUHZWKHFDS)LJSRXULQWRWKHWDQN.HHSWKHÀQVDQGFRLORIWKHK\GUDXOLFPRWRU)LJ$
and Fig. 7) thoroughly cleaned. Quantity 1 litre.
TYRE PRESSURE
Correct tyre pressure is essential for perfect levelness of the cutting deck, and therefore for an evenly
mown lawn.
Pressures must be:
FRONT: 13 x 50/6 1 bar
REAR: 17 x 8.00-8 1.5 bar; 18 x 8.50-8 1.5 bar.
AIR FILTER
&KHFNWKHDLUÀOWHUHYHU\KRXUVRUPRUHIUHTXHQWO\LIZRUNLQJLQDYHU\GXVW\HQYLURQPHQW)LJ
Check the mesh-type air-intake grille for engine cooling (Fig. 5).
7KHH[WHUQDODQGLQWHUQDOJULOOHVPXVWDOZD\VEHNHSWFOHDQWRDYRLGEORFNLQJWKHDLUÁRZQHHGHGIRU
engine cooling (Fig. 5).
.HHSWKHHQJLQHFRPSDUWPHQWWKHK\GURVWDWLFWUDQVPLVVLRQDQGWKHLQWDNHJULOOHFOHDQ
CHECKING THE BLADES AND DECK
A blunt blade tears the grass, leaving it unattractive. The cutting edges of both blades must be sharpened.
7RUHPRYHDEODGHWDNHKROGRILWÀUPO\ZHDULQJZRUNJORYHVDQGXQVFUHZWKHFHQWUDOVFUHZUHPHPEHULQJ
that the screw has a right-hand thread (n. 3, Fig. 1/C). Sharpen both cutting edges using a medium-
grain grinding wheel and check that the blade is balanced by standing it on a round bar inserted in the
central hole. Fit the two cutting blades following the diagram in Fig. 13.
CAUTION!
7LJKWHQWKHÀ[LQJVFUHZQ)LJ&ÀUPO\
$OZD\VUHSODFHGDPDJHGRUFURRNHGEODGHVQHYHUDWWHPSWWRUHSDLUWKHP:KHQÀWWLQJDOZD\VIROORZ
the diagram (Fig. 13).
ALWAYS USE ORIGINAL BLADES! If they are worn they can be turned round since they have two cutting
edges.
910 mm CUTTING DECK
ADJUSTING THE 910 mm CUTTING DECK
Levelness of the cutting deck is essential in order to obtain an evenly mown lawn.
3DUNWKHPRZHURQDÁDWVXUIDFHDQGFKHFNWKDWWKHW\UHSUHVVXUHLVFRUUHFW$GMXVWWKHULJKWDQGOHIW
DGMXVWPHQWGHYLFHVVRWKDWWKHHGJHRIWKHFXWWLQJGHFNLVDWWKHVDPHGLVWDQFHIURPWKHÁRRUPP
on both sides (with the operator sitting on board) Fig. 14 - 14/A.
If you are unable to level off the cutting deck, contact an Authorised After-Sales Service Centre.
ENGINE - BLADE BELT 910 mm CUTTING DECK
The engine - blade belt is self-adjusting. No adjustment is required. Simply check the spring tension
(Fig. 15).
If the belt becomes twisted or comes off, check the dimensions stated below, keeping the cutting deck
at the highest setting (“travel”):
1) 170 mm from the edge of the deck to the ground (Fig. 24).
2) 170 mm from the rear edge of the deck to the ground (Fig. 24).
3) Adjust the registers (Fig. 14 - 14/A).
4) Take care when positioning the belt guides; move them towards the belt, checking the cutting deck
at the various height settings (A, Fig. 12). Check that during operation the belt is always in the centre
of the stretcher (A, Fig. 15). The stretcher has to stick about 5/8 mm out of the frame, as shown in
Fig. 25.
Скачать «GRILLO Climber 9.21» — 6,22 МБ СкачатьСкачиваний: 0
Все руководства категории →
Нашли ошибку?