Инструкция по эксплуатации Carrier 42UQV — страница 3

Press

: Move the louver in the desired vertical direction.

Press

: Swing the air automatically and press again to stop.

For horizontal direction adjust manually.

Note:

• Do not move the louver manually by others.

The louver may automation positioning by some operation mode.

1 Infrared signal emitter 2 Start/Stop button (

3 Mode select button (

4 Temperature button (

5 Fan speed button (

6 Swing louver button (

7 Set louver button (

8 On timer button (

9 Off timer button (

! ECO Sleep button (

" Setup button (

# Clear button (

$ Memory and Preset button (

% High power button (

& Economy button (

( Quiet button (

) Filter reset button (

~ Set clock button (

+ Check button (

Reset button (

1 Press

: Select Cool

Heat or Fan only

2 Press

: Set the desired temperature.

Cooling: Min 17°C Heating: Max 30°C Fan Only:

No temperature indication

3 Press

: Select AUTO LOW LOW+

MED+

or HIGH

For dehumidification a moderate cooling performance is controlled automatically.

Press

: Select Dry.

Press

: Set the desired temperature

To automatically control room temperature and airflow for faster cooling or heating operation (except in DRY and FAN ONLY mode)

Press

: Start and stop the operation.

To automatically control room to save energy (except in DRY and FAN ONLY
mode)

Press

: Start and stop the operation.

Note: Cooling operation; the set temperature will increase automatically 1 degree hour for 2 hours (maximum 2 degrees increase) For heating operation the set temperature will decrease.

In case of the misplaced or discharged remote control

• Pressing the RESET button the unit can start or stop without using the remote control.

• Operation mode is set on AUTOMATIC operation preset temperature is 24°C and fan operation is automatic speed.

Set the timer when the air conditioner is operating.

Setting ON Timer

Setting OFF Timer

Press

: Set the desired ON timer.

Press

: Set the desired OFF timer.

Press

: Set the timer.

Press

: Set the timer.

Press

: Cancel the timer.

Press

: Cancel the timer.

Daily timer allows the user to set both the ON & OFF timers and will be activated on a daily basis.

Setting Everyday Timer

Press

: Set the ON timer.

Press

Press

: Set the OFF timer.

Press button during the ( or ) mark flashing.

• During the every day timer is activating both arrows ( ) are indicated.

Note:

• Keep the remote control in accessible transmission to the indoor unit; otherwise the time lag of up to 15 minutes will occur.

• The setting will be saved for the next same operation.

Preparing Filters

1 Open the air inlet grille and remove the air filters.
2 Attach the filters (see detail in the accessory sheet).

Loading Batteries (when use wireless operation.)

1 Remove the slide cover.
2 Insert 2 new batteries (AAA type)
following the (+) and (–) positions.

Clock Setup

1 Push by tip of the pencil

If timer indication is flashing go to the next step 2.

2 Press or

: adjust the time 3 Press

: Set the time

Remote Control Reset

Push by tip of the pencil or

1 Remove the battery.

2 Press

3 Insert the battery.

PREPARATION BEFORE USE

AIRFLOW DIRECTION

REMOTE CONTROL

To automatically select cooling heating or fan only operation

1 Press

: Select A.

2 Press

: Set the desired temperature.

3 Press

: Select AUTO LOW LOW+

MED+

or HIGH

AUTOMATIC OPERATION

COOLING HEATING FAN ONLY OPERATION

DRY OPERATION

Hi-POWER OPERATION

ECO OPERATION

TEMPORARY OPERATION

TIMER OPERATION

Note:

• The provided Remote Controller is a wireless type which also can be used as a wire Please see “How to Connect The Remote Controller for Wired Operation” located in installation instruction in case of wired control is required.

- In wire operation remote controller will return to initial condition (PRESET TIMER and CLOCK will return to initial condition) when user shutdown power supply of Air conditioner.

Carrier1110655103(01_EN).indd 3

Carrier1110655103(01_EN).indd 3

2/6/13 3:19 PM

2/6/13 3:19 PM