Инструкция BEKO EV 6800 — страница 3

Инструкция

PDF

3,01 МБ

Стиральные машины

MilaДок507

Инструкция для BEKO EV 6800 на русском языке. Документ можно использовать для ознакомления с информацией, относящейся к данной модели.

Инструкция представлена в формате PDF, просмотр, скачивание на компьютер, смартфон бесплатно. Возможность печати зависит от используемой программы и настроек устройства. Содержание, структура и объём документа могут различаться в зависимости от модели, версии и редакции руководства. Перед использованием рекомендуется убедиться, что инструкция соответствует вашей модели.

3 - EN

kilograms. Place the product on a solid and flat

floor that has sufficient load carrying capacity!

• Donotplacetheproductonthepowercable.

• Donotinstalltheproductatplaceswhere

temperaturemayfallbelow0ºC.

• Placetheproductatleast1cmawayfromthe

edges of other furniture.

Removing packaging reinforcement

Tiltthemachinebackwardstoremovethe

packaging reinforcement. Remove the packaging

reinforcementbypullingtheribbon.

Removing the transportation locks

Donotremovethetransportationlocksbefore

taking out the packaging reinforcement.

Removethetransportationsafetyboltsbefore

operating the washing machine! Otherwise, the

productwillbedamaged.

Loosenalltheboltswithasuitablespanneruntil

they rotate freely (C). Remove transportation safety

boltsbyturningthemgently.Attachtheplastic

coverssuppliedintheUserManualbagintothe

holes on the rear panel. (P)

 Keepthetransportationsafetyboltsinasafe

place to reuse when the washing machine

needstobemovedagaininthefuture.

Never move the product without the

transportationsafetyboltsproperlyfixedin

place!

Connecting water supply

 Thewatersupplypressurerequiredtorun

theproductisbetween1to10bars(0.1–10

MPa).Itisnecessarytohave10–80litersof

water flowing from the fully open tap in one

minute to have your machine run smoothly.

Attach a pressure reducing valve if water

pressure is higher.

 Ifyouaregoingtousethedoublewater-inlet

product as a single (cold) water-inlet unit, you

must install the supplied stopper to the hot

watervalvebeforeoperatingtheproduct.

(Appliesfortheproductssuppliedwithablind

stopper group.)

 Ifyouwanttousebothwaterinletsofthe

product, connect the hot water hose after

removing the stopper and gasket group from

the hot water valve. (Applies for the products

suppliedwithablindstoppergroup.)

Modelswithasinglewaterinletshouldnotbe

connectedtothehotwatertap.Insuchacase

the laundry will get damaged or the product will

switch to protection mode and will not operate.

Donotuseoldorusedwaterinlethoseson

thenewproduct.Itmaycausestainsonyour

laundry.

1. Connect the special hoses supplied with the

product to the water inlets on the product. Red

hose(left)(max.90ºC)isforhotwaterinlet,

bluehose(right)(max.25ºC)isforcoldwater

inlet.

Ensure that the cold and hot water connections

are made correctly when installing the product.

Otherwise, your laundry will come out hot at the

end of the washing process and wear out.

Tightenallhosenutsbyhand.Neveruseawrench

when tightening the nuts. Open the taps completely

after making the hose connection to check

forwaterleaksattheconnectionpoints.Ifany

leaks occur, turn off the tap and remove the nut.

Retighten the nut carefully after checking the seal.

To prevent water leakages and damages caused

bythem,keepthetapsclosedwhenthemachine

is not in use.

Connecting to the drain

• Theendofthedrainhosemustbedirectly

connected to the wastewater drain or to the

washbasin.

Yourhousewillbefloodedifthehosecomes

out of its housing during water discharge.

Moreover, there is risk of scalding due to

high washing temperatures! To prevent such

situations and to ensure smooth water intake

and discharge of the machine, fix the end of the

discharge hose tightly so that it cannot come

out.

• Thehoseshouldbeattachedtoaheightofat

least 40 cm, and 100 cm at most.

• Incasethehoseiselevatedafterlayingiton

the floor level or close to the ground (less than

40cmabovetheground),waterdischarge

becomesmoredifficultandthelaundrymay

come out excessively wet. Therefore, follow the

heightsdescribedinthefigure.

• Topreventflowingofdirtywaterbackintothe

machine and to allow for easy discharge, do

not immerse the hose end into the dirty water

ordonotdriveitinthedrainmorethan15cm.

Ifitistoolong,cutitshort.

• Theendofthehoseshouldnotbebent,it

shouldnotbesteppedonandthehosemust

notbepinchedbetweenthedrainandthe

machine.

• Ifthelengthofthehoseistooshort,useit

byaddinganoriginalextensionhose.Length

ofthehosemaynotbelongerthan3.2m.

Скачать «BEKO EV 6800» — 3,01 МБ СкачатьСкачиваний: 0

Инструкция BEKO EV 6800 — страница 3

Другие руководства из этой категории